valutazioni - 3, GPA: 4.7
(
)
)
|
Facilità d'uso
C. ITEMS NOT COVERED BY PeCo WARRANTY. Engines and batteries attached to PeCo products are covered under a separate warranty by the respective manufacturer. D. UNAPPROVED ALTERATION OR MODIFICATION. All obligations of PeCo, Inc. under this warranty shall be terminated if products are altered or modified in ways not approved by PeCo, Inc. E. ACCIDENTS AND NORMAL MAINTENANCE. The warranty covers only defective material and workmanship. It does not cover depreciation or damage caused by normal wear, accident, improper use or abuse of products. The cost of normal maintenance and normal replacement of service items such as belts, cutting blades, hoses, etc., which are not defective shall be paid for by the purchaser. WARRANTY MODEL 37610701 - 04 PeCo SAFETY Outdoor Power Equipment Institute Recommendations WARNING TO PURCHASERS OF INTERNAL COMBUSTION ENGINE EQUIPPED MACHINERY OR DEVICES IN THE STATE OF CALIFORNIA: The equipment which you have purchased does not have a spark arrester muffler. If this equipment is to be used on any forest covered and brush covered land or grass covered unimproved land in the state of California, the law requires that a spark arrester muffler be installed and be in effective working order. The spark arrester must be attached to the exhaust system and comply with Section 4442 of the California Public Resources Code. 7. Always stop Vac engine when emptying the container. 8. Stop tractor and vac engines and remove spark plug wire before removing or replacing hose, boot, blower cone or performing any maintenance. 9. Mow up and down the face of slopes (not steeper than 10 degrees); never across the face of the slope. 10. It is recommended that the container be kept only half full when negotiating any slopes. Start mowing on slopes when the container is empty. 11. Inspect your lawn and remove any foreign objects before mowing. Never deliberately run mower across any foreign object. 12. Wear ear protection if noise level is offensive. 1. Read the owner's manual carefully and familiarize yourself with the proper use of your attachment. Do not allow anyone who is not acquainted with the Safety Instructions to use your attachment. 2. Know the controls and how to stop quickly. READ THE OWNER'S MANUAL! 3. Do not allow children to operate the vehicle. Do not allow adults to operate it without proper instruction. 4. Be especially watchful of children and pets darting into the area while operating. 5. Keep your eyes and mind on your tractor while mowing or operating your attachment. Don't let others distract you. 6. Do not attempt to operate your tractor or mower when not in the driver's seat. WARNING! Do not work around the mower deck boot or the blower area until you are certain that the mower blades and the blower fan have stopped rotating. WARNING! To avoid serious injury, perform maintenance on the vacuum collector ONLY AFTER STOPPING THE TRACTOR ENGINE AND WAITING FOR ALL MOVING PARTS TO COME TO A COMPLETE STOP. Set the parking brake. Always remove the ignition key before beginning the maintenance WARNING! For your personal safety, ALWAYS mow UP and DOWN the face of slopes and NEVER across the face. NEVER attempt to mow excessively steep slopes and use caution when turning on any slope. WARNING! NEVER operate the mower unless the discharge guard and either the deflector assembly or the vacuum collector adapter are fastened securely in place. MODEL 37610701 - 04 PeCo 3 HOLES TO MOUNT TO TRACTOR MOWER FRAME A B ASSEMBLY STEP 1: Remove plate on rear of mower as shown. Redrill top two holes for a 3/8"-16 hex bolt to mount Mount Plate onto mower frame. FIG. 1-1 DESIGNATION OF HOLES ON THE MOUNT PLATE STEP 2: Use (2) 3/8"-16 x 2" (#K1208) , and (2) 3/8"-16 flange nuts (#K1215) to secure Mount Plate (A) to mower frame. Use (2) 1" spacers (#S0138) between Mount Plate (A) and mower frame. Place (1) Bracket (B) on each side of Mount Plate (A). Use (1) 3/8"-16 x 3/4" hex bolt (#K1190) and (1) 3/8"-16 flange nut (#K1215) to mount each bracket. Use existing bolts from mower frame to mount Bracket (B) to mower. Use figure 1-1 to place bolts. HOLES TO MOUNT TO TRACTOR MOWER FRAMEB A MODEL 37610701 - 04 PeCo ASSEMBLY STEP 3: Slide Engine Mount Arm (B) into the receiver on the Mount Plate (A) and fasten by dropping in ball pin (#J0248). Place Engine/ Blower Assembly onto Engine Mount Arm (B) and fasten with (4) 5/16"-18 x 1 1/2 hex bolts (#K1157) and (4) 5/16"-18 flange nuts. Tighten nuts and bolts. STEP 4: The ears of the Cone (A) should fit underneath the two threaded bosses on the Blower Face (B). Secure with (2) 5/16"-18 x 2" cone bolts. TIGHTEN CONE BOLTS BEFORE EACH USE! A B B A A BImpeller Blade Replacement To remove: Remove hex bolts from hub then screw the bolts into threaded holes to remove old blade. (This will push the impeller off the hub.) If the impeller is stuck on hit the base of the impeller between each vein with a hammer then try the bolts again. To replace: Place tapered bushing (A) int...