valutazioni - 5, GPA: 4.2 ( )

Produttore : Nilfisk-ALTO File Size : 1.19 mb File Nome : Lingua di insegnamento:

Wait five minutes and push the reset button back in. Turn the key switch "ON", and try again. An authorized service person should be contacted if the breaker trips again. F G B F A H IED C M L K J Figure #2 CLARKE TECHNOLOGY Operator's Manual -SCRUBTEC 770 / 784 / 795 SCRUBTEC 770 / 784 / 795SCRUBTEC 770 / 784 / 795SCRUBTEC 770 / 784 / 795SCRUBTEC 770 / 784 / 795SCRUBTEC 770 / 784 / 795 -13 Display Screens For SCRUBTEC 770 L, 784 L, 795 L Display Screens For SCRUBTEC 770 L, 784 L, 795 L to Operator Position arrow indicating current position of squeegee (up or down) 3 Indicators are on all the time showing SCREEN 1 current settings. Water “droplets” off when solution is off and they are flashing when solution is on. “Battery” blinks when low voltage occurs. Arrows indicating vacuum status. They are flashing when vac is on and off when vac is off. SCREEN 2 Example SCREEN 3 (Diagnostic) The Diagnostic only. It will not show unless a fault with the machine occurs. When the fault happens the icon and error code will be displayed. See "Common Error Codes" at end of "Maintenance Section". Page -14-CLARKE TECHNOLOGY Operator's Manual -SCRUBTEC 770 / 784 / 795 SCRUBTEC 770 / 784 / 795SCRUBTEC 770 / 784 / 795SCRUBTEC 770 / 784 / 795SCRUBTEC 770 / 784 / 795SCRUBTEC 770 / 784 / 795 MACHINE CONTROLS & FEATURES EN MACHINE CONTROLS & FEATURES EN ("S Class" models only) See Figure #3a, 3b, & 3c. The squeegee lift handle is located below the control handles on the right side. It is used to raise or lower the squeegee. The vac motor is turned on when the handle is lowered. Parking Brake (Optional)See Figure #4. The parking brake prevents movement of the machine. The brake is located on the left hand side of the transaxle motor. Turn the key switch off or disconnect the power to the battery to apply the brake. There is a mechanical lever located on the brake. This lever is an override. To manually release the brake, rotate the lever toward the rear of machine (counter clockwise). To return the brake to normal or to apply the brake, rotate the lever towards the front of the machine (clockwise). NOTE: If the lever is left in the override position, thebrake will not function with the key switch, and themachine will not operate. CAUTION: Do not activate the brake while the machine is moving. Float Shut Off See Figure #5. The shut-off switch for the vac motor is located in the recovery tank. It automatically turns off the vac motor when the recovery tank is full. Figure #3a Figure #4 Figure #3b Figure #5 Figure #3c CLARKE TECHNOLOGY Operator's Manual -SCRUBTEC 770 / 784 / 795 SCRUBTEC 770 / 784 / 795SCRUBTEC 770 / 784 / 795SCRUBTEC 770 / 784 / 795SCRUBTEC 770 / 784 / 795SCRUBTEC 770 / 784 / 795 -15 Page -16- CLARKE TECHNOLOGY Operator's Manual - SCRUBTEC 770 / 784 / 795 HOW TO PREPARE THE MACHINE FOR OPERATION How To Install The Batteries The Scrubtec machines use six 6-volt batteries. The batteries are located in the battery compartment under the recovery tank. To Install the batteries, follow this procedure: 1. Turn key switch off. 2. Make sure both tanks are empty. 3. Disconnect the hoses from the recovery tank (upper tank) & unplug the vac motor and float switch. 4. Remove the tank support bracket. 5. Remove the recovery tank. 6. Place the batteries in the solution tank as shown in figures 6a and 6b. WARNING: Lifting batteries without help could result in an injury. Get help to lift the batteries. The batteries are heavy. WARNING: Working with batteries can be dangerous. Always wear eye protection and protective clothing when working near batteries. NO SMOKING! 7. Connect the battery cables between batteries and install long battery cable assembly as indicated. See figure 6a and 6b. 8. Install the tank, reconnecting hoses and plugging in vac motor and float switch connectors. Install tank support bracket. NOTE: Charge the batteries before using the machine. Figure #6a Figure #6b 38722B 38722B 38722B 38720B 38720B 38722B 38720B 38722B 38722B HOW TO PREPARE THE MACHINE FOR OPERATION HOW TO PREPARE THE MACHINE FOR OPERATION The electrical power to operate the machine comes from thestorage batteries. Storage batteries need preventive maintenance. WARNING: Working with batteries can be dangerous. Always wear eye protection and protective clothing whenworking near batteries. NO SMOKING! To maintain the batteries in good condition, follow theseinstructions: 1. Keep the electrolyte at the correct level. The correct level is between 6.35mm below the bottom of the tube in each cell and above the tops of the plates. Check the level of the electrolyte each time you charge thebatteries. See figure #7. NOTE: Check the level of electrolyte prior to charging thebatteries. Be sure the plates in each cell are covered withelectrolyte . Do not top off the cells prior to charging thebattery. Electrolyte expands during charging. As a result, the electrolyte could overflow from the cells. Always top offthe cells with distilled water after charging. ...

Scarica la tua

Per scaricare, digitare 2 cifre :