valutazioni - 1, GPA: 5 ( )

Produttore : Desa Tech File Size : 1.65 mb File Nome : Lingua di insegnamento:

These two holes are 14 inches apart from their centers. Attach mounting bracket to wall in one of two ways: 1. Attaching to wall stud 2. Attaching to wall anchor Attaching to Wall Stud: This method provides the strongest hold. Insert mounting screws through mounting bracket and into wall studs. Attaching to Wall Anchor: This method allows you to attach mounting bracket to hollow walls (wall areas between studs) or to solid walls (concrete or masonry). Decide which method better suits your needs. Either method will provide a secure hold for the mounting bracket. Figure 5 - Attaching Thermostat Sensing Bulb INSTALLING HEATER TO WALL Mounting Bracket Locate mounting bracket in heater carton. Remove mounting bracket from heater carton. Figure 7 - Removing Front Panel Of Heater Removing Front Panel Of Heater 1. Remove the four painted screws, two on each side of front panel. 2. Pull bottom of front panel forward, then out. 3. Remove any remaining packaging materials. Figure 6 - Mounting Bracket Clamp Thermostat Sensing Bulb INSTALLATION Installing Heater To Wall (Cont.) 9 INSTALLATION Continued 2. Mark screw locations on wall (see Figure 8). Note:Only mark last hole on each end of mounting bracket. Insert mounting screws through these holes only. 3. Remove tape and mounting bracket from wall. 18 3/4" Min. 12" Min. 14" Adjoining WallOnly Insert Mounting Screws Through Last Hole On Each End Floor 30,000 Btu/hr Models 14" 18 3/4" Min. 8" Min. Adjoining WallOnly Insert Mounting Screws Through Last Hole On Each End Floor 20,000 Btu/hr Models Figure 8 - Mounting Bracket Clearances Attaching Mounting Bracket To Wall Note:Wall anchors, mounting screws, and spacers are in hardware package. The hardware package is provided with heater. Attaching To Wall Stud Method For attaching mounting bracket to wall studs 1. Drill holes at marked locations using 9/64" drill bit. 2. Place mounting bracket onto wall. Line up last hole on each end of bracket with holes drilled in wall. 3. Insert mounting screws through bracket and into wall studs. 4. Tighten screws until mounting bracket is firmly fastened to wall studs. Attaching To Wall Anchor Method For attaching mounting bracket to hollow walls (wall areas between studs) or solid walls (concrete or masonry) 1. Drill holes at marked locations using 5/16" drill bit. For solid walls (concrete or masonry), drill at least 1" deep. 2. Fold wall anchor as shown in Figure 9. 3. Insert wall anchor (wings first) into hole. Tap anchor flush to wall. 4. For thin walls (1/2" or less), insert red key into wall anchor. Push red key to “pop” open anchor wings. IMPORTANT:Do not hammer key! For thick walls (over 1/2" thick) or solid walls, do not pop open wings. 5. Place mounting bracket onto wall. Line up last hole on each end of bracket with wall anchors. 6. Insert mounting screws through bracket and into wall anchors. 7. Tighten screws until mounting bracket is firmly fastened to wall. Placing Heater On Mounting Bracket 1. Locate two horizontal slots on back panel of heater. 2. Place heater onto mounting bracket. Slide horizontal slots onto stand-out tabs on mounting bracket. Figure 9 - Folding Anchor Figure 10 - Popping Open Anchor Wings For Thin Walls Horizontal Slots Stand-Out Tab Mounting Bracket (attached to wall) Figure 11 - Mounting Heater Onto Mounting Bracket For more information, visit more information, visit 107882-01E 10 10 INSTALLATION Installing Heater To Wall (Cont.) Mounting Heater To Floor INSTALLATION Continued Installing Bottom Mounting Screws 1. Locate two bottom mounting holes. These holes are near bottom on back panel of heater (see Figure 12). 2. Mark screw locations on wall. 3. Remove heater from mounting bracket. 4. If installing bottom mounting screws into hollow or solid wall, install wall anchors. Follow steps 1 through 4 under Attaching To Wall Anchor Method, page 9. If installing bottom mounting screw into wall stud, drill holes at marked locations using 9/64" drill bit. 5. Replace heater onto mounting bracket. 6. Place spacers between bottom mounting holes and wall anchor or drilled hole. 7. Hold spacer in place with one hand. With other hand, insert mounting screw through bottom mounting hole and spacer. Place tip of screw in opening of wall anchor or drilled hole. 8. Tighten both screws until heater is firmly secured to wall. Do not over tighten. Note:Do not replace front panel at this time. Replace front panel after making gas connections and checking for leaks (see pages 11 and 12). MOUNTING HEATER TO FLOOR Mounting Base Feet to Heater 1. Lay heater cabinet on its back on a table with the heater bottom overhanging the table edge. 2. Align holes in base foot with mounting holes on bottom of cabinet (see Figure 13). 3. Secure base foot to heater using sheet metal screws. 4. Repeat for other side. Mounting Base Feet to Floor (Where required by local code) 1. Remove front cover (see Removing Front Panel of Heater, page 8). 2. Posit...

Scarica la tua

Per scaricare, digitare 2 cifre :