Log:
valutazioni - 4, GPA: 3.8 ( )

Istruzioni per l'uso Desa, Modello GP30 GN30T

Produttore : Desa
File Size : 3.14 mb
File Nome :
Lingua di insegnamento: en
Vai a scaricare



Facilità d'uso


IMPORTANT:Install an equipment shutoff valve in an accessible location. The equipment shutoff valve is for turning on or shutting off the gas to the appliance. Apply pipe joint sealant lightly to male NPT threads. This will prevent excess sealant from going into pipe. Excess sealant in pipe could result in clogged heater valves. WARNING: Use pipe joint sealant that is resistant to liquid petroleum (LP) gas. Install sediment trap in supply line as shown in Figure 15. Locate sediment trap where it is within reach for cleaning. Locate sediment trap where trapped matter is not likely to freeze. A sediment trap traps moisture and contaminants. This keeps them from going into heater controls. If sediment trap is not installed or is installed wrong, heater may not run properly. IMPORTANT: Hold the pressure regulator with wrench when connecting it to gas piping and/or fittings. Do not over tighten pipe connection to regulator. The regulator body could be damaged. Note:Burner Pressure bracket not Regulator shown for 3/8" NPT Pipe Nipple Heater Cabinet Tee Joint Test Reducer Gauge Bushing to Con 1/8" NPT nection* 1/8" NPT Plug Tap Tee Joint Sediment Pipe Trap Cap (11" W.C. to 14" W.C. Nipple Equipment Shutoff Valve * 3" Minimum Natural Gas From Gas Meter (5" W.C. to 10.5" W.C. Pressure) Propane/LP From External Regulator Ground Joint Union clarity Figure 15 - Gas Connection Pressure) * A CSA design-certified equipment shutoff valve with 1/8" NPT tap is an acceptable alternative to test gauge connection. Purchase the optional CSA design-certified equipment shutoff valve from your dealer. See Accessories, page 27. For more information, visit more information, visit 107884 Forr morre iinfforrmattiion,, viisiitt 12 INSTALLATION Continued INSTALLATION Checking Gas Connections Figure 18 - Checking Gas Joints for Propane/LP Gas Figure 16 - Equipment Shutoff Valve Equipment Shutoff Valve Propane/LP Supply Tank Thermostat Gas Valve ON POSIT O PO Open Closed Equipment Shutoff Valve Figure 17 - Checking Gas Joints for Natural Gas Equipment Shutoff Valve Gas Meter Thermostat Gas Valve Pressure Testing Heater Gas Connections 1. Open equipment shutoff valve (see Figure 16). 2. For natural gas open main gas valve located on or near gas meter. For propane/LP gas open propane/LP supply tank valve. 3. Make sure control knob of heater is in the OFF position. 4. Check all joints from equipment shutoff valve to thermostat gas valve (see Figure 17 or 18). Apply a noncorrosive leak detection fluid to all joints. Bubbles forming show a leak. 5. Correct all leaks at once. 6. Light heater (see Operating Heater, starting on page 13). Check all other internal joints for leaks. 7. Turn off heater (see To Turn Off Gas to Appliance, page 14 or 15, depending on your model heater). 8. Replace front panel. WARNING: Test all gas piping and connections for leaks after installing or servicing. Correct all leaks at once. WARNING: Never use an open flame to check for a leak. Apply a noncorrosive leak detection fluid to all joints. Bubbles forming show a leak. Correct all leaks at once. CAUTION: For propane/LP gas, make sure external regulator has been installed between propane/LP supply and heater. See guidelines under Connecting to Gas Supply, page 10. Pressure Testing Gas Supply Piping System Test Pressures In Excess Of 1/2 PSIG (3.5 kPa) 1. Disconnect appliance with its appliance main gas valve (control valve) and equipment shutoff valve from gas supply piping system. Pressures in excess of 1/2 psig will damage heater regulator. 2. Cap off open end of gas pipe where equipment shutoff valve was connected. 3. Pressurize supply piping system by either opening propane/LP supply tank valve for propane/LP gas or opening main gas valve located on or near gas meter for natural gas, or using compressed air. 4. Check all joints of gas supply piping system. Apply a noncorrosive leak detection fluid to all joints. Bubbles forming show a leak. 5. Correct all leaks at once. 6. Reconnect heater and equipment shutoff valve to gas supply. Check reconnected fittings for leaks. Test Pressures Equal To or Less Than 1/2 PSIG (3.5 kPa) 1. Close equipment shutoff valve (see Figure 16). 2. Pressurize supply piping system by either opening propane/LP supply tank valve for propane/LP gas or opening main gas valve located on or near gas meter for natural gas, or using compressed air. 3. Check all joints from gas meter for natural gas (see Figure 17) or propane/LP supply tank for propane/LP gas, to equipment shutoff valve (see Figure 18). Apply a noncorrosive leak detection fluid to all joints. Bubbles forming show a leak. 4. Correct all leaks at once. CHECKING GAS CONNECTIONS OPERATING HEATER (MANUAL CONTROL MODELS) For Your Safety Read Before Lighting Lighting Instructions 13 OPERATING HEATER MANUAL CONTROL MODELS WARNING: If you do not follow these instructions exactly, a fire or explosion may result causing property dam...

Questo manuale è adatto anche per i modelli :
Riscaldamento a gas - GN30 (3.14 mb)
Riscaldamento a gas - GP30T GWN20 (3.14 mb)
Riscaldamento a gas - GWP20 GWN20T (3.14 mb)
Riscaldamento a gas - GWP20T GWN30T (3.14 mb)

Scrivi la tua opinione del dispositivo



Il messaggio
Il tuo nome :
Inserire le due cifre :
capcha





categorie