Log:
valutazioni - 4, GPA: 4 ( )

Istruzioni per l'uso Silvercrest, Modello PS2-WLC

Produttore : Silvercrest
File Size : 538.59 kb
File Nome : 10200c83-8a13-489a-8667-c455384f42e0.pdf
Lingua di insegnamento: en
Vai a scaricare



Facilità d'uso


User guide We hope you enjoy using our PS2 ™ 2.4 GHz wireless controller. Please read this guide thoroughly before using the unit. 4- WAY button TURBO button SELECT button PROGRAM button START button CONNECT button .. button .. button .. button X button RIGHT ANALOGUE JOYSTICK (when pressed: R3) RX-LED ANALOGUE button MODE-LED LEFT ANALOGUE JOYSTICK (when pressed: L3) X button R1 button ON/OFF switch Battery compartment L1 button L2 button Connection plug RX-LED CONNECT button POWER-LED 1. Product description This device is a wireless controller specifically for use with PlayStation2™ . It can also be used with PSONE™ and PSX ™. The controller works at a frequency of 2.4 GHz, has a double vibration feature as well as all other functions of the original SONY units. The controller also has Turbo and Program functions. 2. Included 1 Controller; 1 receiver; 1 user manual 3. Product features Power Supply: 3 x 1.5 V AAA batteries Operating time: More than 6 hours Transmission: 2.4 GHz multi- channel transmission Range of action: 10 m Special functions: Turbo function, programmable buttons with memory, forced connection 4. Connecting the receiver Insert the receiver plug into the appropriate slot on the PlayStation™ console and then switch on the PlayStation™. The POWER-LED on the receiver will come on. The RXLED will remain on as soon as the receiver is connected to the controller. 5. Inserting / replacing the batteries Before using the controller insert the batteries into the battery compartment on the back of the unit. To do this, open the battery compartment , insert the new batteries according to the polarity and close the compartment. Please ensure the controller has been switched off before you replace the batteries. Please also read the information on safe disposal of batteries. - 1 - PS2-WLC Controller Note: • Please only use batteries or rechargeable batteries with a nominal voltage of 1.5 V. • Please ensure the batteries are always inserted according to the correct polarity. Replace the batteries with the same brand or similar batteries. • There is a risk of explosion if the batteries are not replaced correctly. • Do not attempt to recharge a non-rechargeable battery. There is a risk of explosion. • Batteries / rechargeable batteries can be fatal if swallowed. Please store batteries out of reach of small children. Seek medical help immediately if a battery has been swallowed. • Do not expose the batteries to heat or flames. Never short-circuit batteries; never try to force open batteries; never attempt to recharge non-rechargeable batteries. Batteries may otherwise explode and cause serious injury. • Never replace the batteries in a potentially explosive area. Sparks may be generated while the batteries are being inserted or replaced which could cause an explosion. Potentially explosive areas are often signposted as such, but not always. These include filling stations, such as under below-deck areas on boats, fuel transmission stations, fuel depots, areas in which the air may contain chemicals or particles such as grain, dust or metallic powder, as well as all other areas in which you would normally be asked to switch off the engine of your car. 6. Switching on and off The on/off switch is on the back of the device. To switch the unit off move the switch to the “OFF” position and to the “ON” position to switch it on. 7. Connecting the controller The connection mode will initiate as soon as the On/Off switch on the underside of the unit is switched to the ON position. The RX-LED and MODE-LED lights will light up briefly at the same time. If the RX- LED comes on, the device is trying to establish a connection with the receiver. The RX LED goes out as soon as a connection has been established. 8. Force connection If several wireless controllers are connected at the same time, you can use the force connection method to select a single controller. Press the CONNECT button on the hand-held unit and then press the CONNECT button on the receiver within 15 seconds to establish a connection. Now press the L3 button and the SELECT button on the hand- held unit and the CONNECT button on the receiver at the same time for 15 seconds. 9. Mode selection Many games support an analogue controller which permit more precise input than with digital controllers. There must be a connection to the receiver before you can switch between the digital and analogue modes. To do this, press the ANALOGUE button . The MODE-LED lights up in analogue mode. The MODE-LED is off in digital mode. Note: • The default mode is digital. • Not all games support digital mode. • You may have to finish the game before switching between modes. 10. Energy-saving mode The unit is equipped with an energy-saving mode to conserve energy and prolong battery life. This mode is activated in the following situations: • where no connection has been established between the unit and the receiver after 3 seconds • where the unit and receiver are connected but th...


Scrivi la tua opinione del dispositivo



Il messaggio
Il tuo nome :
Inserire le due cifre :
capcha





categorie