valutazioni - 1, GPA: 3
(
)
)
|
Facilità d'uso
PLEASE SHIP THEM WITHOUT CAGE PROPERLY PROTECTED DURING SHIPPING. LOST WORLD, VIRTUA FIGHTER 3, SUPER GT, SEGA BASS FISHING, STRIKER 2 HARLEY DAVIDSON, RALLY 2, DAYTONA 2, DIRT DEVILS, HOUSE OF THE DEAD 2, OCEAN HUNTER, STAR WARS TRILOGY, ZOMBIE REVENGE, CRAZY TAXI, ARILINE PILOTS, 18 WHEELER 4 . ASSEMBLING AND INSTALLATION •Assembling should be performed as per this manual. Since this is a complex machine, erroneous assembling may cause damage to the machine, or malfunctioning to occur. •When assembling, be sure to perform work by plural persons. Depending on the assembly work, there are some cases in which a single person performing the work can cause personal injury or parts damage. •Be careful so as not to damage wirings. Damaged wiring can cause electric shock and short circuit hazards. When carrying out the assembly work, follow the procedure in the following 5-item sequence: ASSY OF THE CABINET SECURING IN PLACE (ADJUSTER ADJUSTMENT) POWER SUPPLY ASSEMBLING CHECK Note that the tools such as a phillips screwdriver and wrench for M16 hexagon bolt w/24 mm width across flats are required for the assembly work. ASSY OF CABINET Permanantly tightening the hex bolts should not be completed until the leg levelers are adjusted properly. NOTE: Game is shipped fully assembled. No assembly required. 1 2 3 4 1 2 SECURING IN PLACE (ADJUSTER ADJUSTMENT) Be sure to have all the Adjusters make contact with the floor surface. Unless the Adjusters come into contact with the floor surface, the Cabinet can move of itself, causing an accident. This machine has 4 each of casters and adjusters (shown below). When the installation position is determined, cause the adjusters to come into contact with the floor directly, make adjustments in a manner so that the casters will be raised approximately 5mm. from the floor and make sure that the machine position is level. 1 Move the machine to the installation position. Be sure to provide adequate space allowing the player to get on and off. 2 3 Have all of the Leg Adjusters make contact with the floor. Adjust the height of the Leg Adjusters by using a wrench so that the machine's position is kept level. After making adjustments, fasten the leg Adjuster Nut upward and secure the height of the Leg Adjuster. 3 POWER SUPPLY Ensure that the power cord is not exposed on the surface (passage, etc.). If exposed, they can be caught and are susceptible to damage. If damaged, the cord can cause an electric shock or short circuit. Ensure that the wiring position is not in the customer's passage way or the wiring has protective covering. Connect the game to the power supply and turn on power to the game. Before connecting power supply be sure that power switch is off 2 1 Turning the AC unit’s main switch on will cause the machine to start the power check and network check automatically. In the Power On check, the steering wheel turns left and right, and then returns to the centering position and stops. In this check, the values of the VR inside the control panel are corrected. 3 Until this check is finished, and the steering wheel stops, do not touch the steering wheel or play the game. If you do, the steering reaction during the game (reaction at the time of course-out or crash) can not be obtained correctly. In the case of an abnormal reaction during the game, turn power on again from the beginning and complete the power on check. 4 ASSEMBLING CHECK In the TEST MODE, ascertain that the assembly has been made correctly and that the IC BOARD is satisfactory. In the test mode, perform the following test: (1) MEMORY TEST MEMORY TEST MODE RAM TEST IC29 GOOD IC34 GOOD IC16 GOOD IC18 GOOD IC20 GOOD IC22 GOOD IC9 GOOD IC10 GOOD IC11 GOOD IC12 GOOD PRESS TEST BUTTON TO EXIT (2) C.R.T. TEST C.R.T. TEST 1/2 RED GREEN BLUE WHITE PRESS TEST BUTTON TO CONTINUE Selecting the RAM TEST item on the test mode menu screen causes the on-board memory to be tested automatically. The game board is satisfactory if the display beside each IC No. shows GOOD. In the TEST mode menu, selecting C.R.T. TEST allows the screen (on which the monitor is tested) to be displayed. Although the monitor adjustments have been made at the time of shipment from the factory, color deviation, etc., may occur due to the effects of geomagnetism, the location of the building’s steel frames and other game machines in the periphery. By watching the test mode screen, make judgement as to whether an adjustment is needed. If it is neccessary, adjust the monitor by refering to Chapter 12. C.R.T. TEST 2/2 PRESS TEST BUTTON TO EXIT (3) INPUT TEST INPUT TEST COIN CHUTE #1 OFF COIN CHUTE #2 OFF SERVICE OFF TEST OFF START OFF VIEW OFF HORN OFF SHIFT [L] OFF SHIFT [H] OFF SHIFT [R] OFF HANDLE XXH ACCEL XXH BRAKE XXH PRESS TEST + SERVICE BUTTON TO EXIT (4) OUTPUT TEST OUTPUT TEST START LAMP OFF VIEW LAMP OFF HORN LAMP OFF ROLL LEFT OFF ROLL RIGHT OFF ->EXIT SELECT WITH SERVICE BUTTON AND PRESS TEST BUTTON (5) SOUND TEST SOUND TEST B.G.M. EFFECT [ ICS [ -...