Produttore : Drive Medical Design
File Size : 1.19 mb
File Nome : 34464621-abcc-416e-8dc6-568fb06055aa.pdf
|
Facilità d'uso
Surface of the ramp: Is it too slippery? 2. Degree of incline: Is it too steep to attempt alone? 3. Length of ramp: Is it too long for your endurance? 4. Obstacles: Are there any obstacles on the ramp that would necessitate an attendant's assistance? ASSISTANCE IS ALWAYS RECOMMENDED WHEN GOING UP OR DOWN STEEP INCLINES. In order to prevent loss of steering control, or the possibility of tipping over backwards, an attendant is recommended when going up inclines greater than 6°. If it becomes necessary to stop when going up an incline, special care must be taken to avoid abrupt or sudden forward movement when you resume operating the chair to avoid tipping the chair backwards. Always keep the chair under control when going down a ramp or incline. Speed should be controlled at all times. When operating your Cirrus Plus Wheelchair and an obstacle is being approached, care should be taken to prevent the chair from becoming unstable. 2 UNPACKING & ASSEMBLY UNPACKING After removing your Cirrus Plus Wheelchair from the carton please check that you have been supplied with the following main parts as standard specification. 1. The main frame with Motors /gearboxes and front castors attached 2. Front rigging with swing away footrests (Fig. 1) 3. Rear drive wheels (Fig. 2) 4. Anti-tip wheel (Fig. 3) 5. 2 Batteries (Rechargeable sealed lead-acid battery) U1 35 Amp (Seperate Boxes) 6. Battery Tray (Fig. 4) 7. Battery Charger 4 amps 8. Controller P.G. VSI SO (Fig. 15) 9. Motors: 24VDC (Fig. 2) ASSEMBLY Assemble the main parts mentioned as per the following procedure and check the assembly for normal operation. 1. Mount the swing away footrests. 2. Drive wheels, motor / gearbox assemblies / Anti-tip wheels are pre-installed. Fig. 1 Fig. 2 Fig. 3 3 AFTER FOLLOWING ALL THE STEPS IN GENERAL OPERATION PROCEED WITH THE FOLLOWING. 1. There are two batteries. Attach the wiring loom to each battery making sure that the correct polarity is observed. Red wire attach on positive pole (also the red color). Black wire attach on negative pole (also the black color). Connect the power cables (located at front right side)to the appropriate plugs and ensure that the power cables are clear of obstacles when replacing the battery box lid. Tighten the battery box- securing strap. (Fig. 15) 2. Place batteries into battery boxes. Insert the battery box with the external power connection towards the front of the chair. 3. Slide the power control module into the mounting bracket under the armrest and secure it into position. Your control module can be mounted either on the left or right hand side of the chair. 4. Ensure that all the power connections are correctly fitted. Fig. 4. Step 1 Fig. 5. Step 2 Fig. 5. Step 3 Fig. 6. Step 4 4 GENERAL OPERATION 1. Hold the two armrests with your hands. 2. Extend the armrests outwards. 3.Push down on the seat rails to ensure the seat opens fully and locks into the receivers on the wheelchair side frames. 4. Swing the footrests around to the front of the chair and ensures that they lock into place. 5. Optional frame rigidity bar can then be put in place on the back of the seat posts. TO FOLD THE WHEELCHAIR FOR STORAGE OR TRANSPORTATION 1. Fold up the footplates and unlock the levers, which position the footrests. Swing the footplates and leg rests away. Either leave the foot plates in this position (Fig. 8) or remove them completely by lifting each leg rest vertically to clear the front hangers. 2. Remove the Batteries from the Battery tray. 3. Take hold of the middle seat upholstery, one hand at the front and the other at the rear, pull the seat upholstery up. Fig. 8 Fig. 9 5 SPECIAL FEATURES FREEWHEEL LEVERS The Cirrus Plus Wheelchair is equipped with two freewheel levers. (Fig. 10) These levers allow you to disengage the drive motors and maneuver the chair manually. WARNING! DO NOT use your wheelchair while the drive motors are disengaged unless you are in the presence of an attendant! DO NOT disengage the drive motors when your wheelchair is on an incline. The chair could roll down on its own, causing injury! To engage or disengage the freewheel feature: 1. Turn the freewheel levers outward to disengage the drive motors. 2. Turn the free wheel levers inward, to engage the drive motors. NOTE: It is important to remember that when your Cirrus Plus Wheelchair is in freewheel mode, the braking system is disengaged. Fig. 10 6 ARMREST The height adjustable T-type armrest (Fig. 11) is provided as standard equipment on your wheelchairs. Adjustment for the wheelchair is facilitated by a lock pin inserted from the outside of the armrest support at the lower extremity and the top of the armrest post. To activate the ball lock pin simply depress the lever found beside the support tube and remove it from the locating hole. The controller unit can easily be adjusted to different positions in order to meet user's demand. To adjust it, (Fig. 12) loosen the knob and move the mounting tube to the desired position then tigh...