Log:
valutazioni - 1, GPA: 4 ( )

Istruzioni per l'uso Invacare, Modello 1095341

Produttore : Invacare
File Size : 177.25 kb
File Nome : 1095349.pdf
Lingua di insegnamento: en
Vai a scaricare



Facilità d'uso


Remove the seat pan. Refer to REMOVING/INSTALLING THE SEAT PAN in PROCEDURE 4 of the Service Manual, part number 1085787. 3. Remove the back canes. Refer to REMOVING/INSTALLING THE BACK CANES in PROCEDURE 5 of the Service Manual, part number 1085787. 4. Remove the allen screw, spacer and locknut that secure the link bracket to the lower seat frame as shown in DETAIL “A” of FIGURE 1. 5. Remove the shoulder screw and locknut securing the rear of the seat frame to the bearing housing as shown in DETAIL “A” of FIGURE 1. 6. Repeat STEPS 4-5 for opposite side of seat frame. 7. Lift up to remove the seat frame from the base frame. NOTE: When reassembling the seat frame, the front crossbrace will be replaced with the crossmember assembly (insert tube and outer tube) provided in this kit and will be secured with the EXISTING mountingscrews. NOTE: Right and left sides of the seat frame are determined by sitting in the wheelchair. 8. On the left hand side of the seat frame, remove the two (2) EXISTING mounting screws and locknuts that secure the front and rear crossbraces to the brace supports of the seat frame as shown in DETAIL “B” of FIGURE 1. 9. Pull the left hand side of the seat frame away from the front and rear crossmembers. 10. Remove the EXISTING mounting screw, and locknut that secures the other end of the front crossbrace to the front right hand side brace support of the seat frame as shown in DETAIL “B” of FIGURE 1. 11. Remove the front crossbrace from the brace support and discard. 12. Insert one end of the insert tube into the front right hand side brace support. 13. Align mounting holes in the end of the insert tube with the brace support and secure with the EXISTING mounting screw and locknut. 14. Slide the outer tube over the insert tube as shown in DETAIL “B” of FIGURE 1. 15. Align the brace supports of the left hand side of the seat frame with the front and rear crossmembers. 16. Insert the front and rear crossmembers into the brace supports of the left hand side of the seat frame. Reinstall the two (2) EXISTING mounting screws and locknuts. 1 2 Contracture Assembly Insert Tube Washers Mounting Holes Mounting Screws Lock Nuts 2. Align the mounting holes of the contracture footplate assembly with two (2) desired mounting positions of the crossmember assembly. 3. Secure the contracture assembly to the crossmember assembly with two (2) mounting screws, washers and locknuts provided. Securely tighten. 4. If necessary, repeat STEPS 1-6 for the other contracture assembly. FIGURE 3 - REMOVING/INSTALLING THE CONTRACTURE ASSEMBLY - REVERSED MOUNT Installing the Contracture Assembly - Forward Mount (FIGURE 2) NOTE: Refer to the GENERAL WARNINGS and INSTALLATION WARNINGS in the SAFETY SUMMARY of this instruction sheet. NOTE: The number of mounting positions on the contracture assembly may vary due to the width of the wheelchair. 1. Align the mounting holes of the outer tube with the mounting holes of the insert tube of the crossmember assembly. Ins...

Questo manuale è adatto anche per i modelli :
Sedie a rotelle - 1095340 (177.25 kb)
Sedie a rotelle - 1095343 (177.25 kb)
Sedie a rotelle - 1095344 (177.25 kb)
Sedie a rotelle - 1095345 (177.25 kb)

Scrivi la tua opinione del dispositivo



Il messaggio
Il tuo nome :
Inserire le due cifre :
capcha





categorie