valutazioni - 2, GPA: 5
(
)
)
|
Facilità d'uso
9) On the underside of the seat there are two hand knobs, one on each side. Loosening the arm rest tightening knob allows the armrest width to be adjusted or arm rests to be removed. Armrest Angle Adjustment (Fig. 10) Flip up the armrests to allow access to the adjustment screw and lock nut, unscrew the lock nut and screw the bolt in or out to increase or decrease the angle. Re-tighten the lock-nut. Your scooter is dispatched from the factory with the armrests set parallel to the floor. Scooter Length Adjustment (For Scootie & Sunrunner S ) (Fig. 11) The wheel base can be lengthened or shortened depending on its existing settings. The standard length of the scooter can be extended up to 3 inches. To adjust the wheelbase, remove the seat and the chassis cover complete with integral batteries. Remove the locking pin located at the front of the seat post (Fig. 8). Unscrew the red hand lever in front of the pin by turning counter-clockwise. Loosen the clips that secure the wires along the chassis. Slide the inner front section until the location holes become aligned. Insert the locking pin and tighten the red hand lever, insuring when fully secured, the lever is facing the seat post as shown in Fig. 11. Replace the chassis cover with the integral batteries then replace the seat. Scooter Width Adjustment (For XtraLite 3) (Fig. 12) Remove seat as described above. Remove rear basket. Remove U-shaped pins, adjust wheels to proper hole. Replace U-shaped pins. Caution – Width of the wheels MUST be adjusted evenly on both sides to avoid injury. Arm Rest Adjustment Hand Knob Figure 9 Locking Nut and Bolt Adjustment Screw Figure 10 Wheel Base Locking Pin Figure 11 Extend both sides up to 3 inches. U- Shaped pins Figure 12 9/22/2004 8 SCOOTER TILLER CONTROLS (FIG. 13) Speed Controls The speed control allows you to set a speed between 1 (minimum) and 10 (maximum). Battery Level Indicator/Gauge The number of LED bars lit/where the needle sits, shows the amount of charge left in your batteries. The amount of charge will only show at its true level when the scooter is in drive. Caution – Do not allow the LED bars/gauge needle to go out completely as complete discharge of the batteries could cause irreversible damage. Horn A yellow button at the rear of the tiller operates the horn. Thumb Lever Controls The left thumb lever controls the reverse and the right thumb lever controls the forward motion. The amount of pressure applied to each lever will determine the speed the scooter travels at. Release the lever and the scooter will slowly come to a stop and the electromagnetic brake will be applied. On/Off Key Switch Insert the key in the right side of the tiller. Turn the key and the LED bars will light up/the needle will move. For XtraLite 3 and XtraLite 4 make sure to turn on the batteries, and for XtraLite 3 turn on the scooter by the power button located next to the horn. There is a delay before the thumb lever control can be operated, while the controller is checking the circuits. Electromagnetic Brake The brake is automatically operated when the control levers are pressed or released. There is a slight delay when the scooter decelerates; this allows the scooter to come to a smooth stop. Battery Level Indicator Speed Control Dial On/Off Key Switch Horn Button Thumb Lever Control (Forward) Thumb Lever Control (Reverse) Figure 13 9/22/2004 9 FREE WHEEL OPERATION (FIG. 14) The free wheel release lever (red handle) is located next to the right rear wheel (Fig. 14). To disengage the motor, lift up the lever (the scooter can now be pushed). To re-engage the motor push down on the lever. WARNING! Always re-engage the free wheeling device after use. Failure to do so may result in injury. Anti-tip wheels The anti-tip wheels are located at the rear of the scooter frame (Fig. 14). The scooter should not be used unless the anti-tipping wheels are in place. Shoprider® Mobility Products, Inc. is not responsible for damage or injury incurred due to improper or misuse of the scooter. Free Wheel Lever (Red) Anti-Tip Wheels Figure 14 STARTING TO DRIVE YOUR SCOOTER Getting Started • Select a level area with plenty of space. • Mount the scooter, either by lifting the arm and sliding onto the seat or rotate the seat outwards and then rotate the seat back to face the tiller. • Adjust the tiller and seat as previously described. Starting Scooter Movement • Ensure that you are seated in a comfortable position. • Turn the key to the on position. • Your speed setting should be on 1 or 2. • Push your right hand thumb lever and the scooter will move forward slowly. The harder you press, the faster the scooter goes but will only reach the speed level that has been selected. • Release the lever and the scooter will slowly come to a stop as the magnetic brake automatically engages. 9/22/2004 10 Steering Steering the scooter is light and easy. Ensure when starting off you give a wide clearance when turning so that the rear wheels clear any obstacle that ...
Questo manuale è adatto anche per i modelli :Sedie a rotelle - Scootie TE-787NA (502.04 kb)