valutazioni - 3, GPA: 4.3
(
)
)
|
Facilità d'uso
Allow at least one inch of space on both sides. Do not operate the UPS where the temperature and humidity are outside the specified limits. Refer to Specifications at the APC web site, PLACEMENT INSTALLING THE SMART-UPS To install the Smart-UPS, follow these basic steps. Details are provided on the following pages. 1. Install the mounting rails in the rack. 2. Remove the battery module. 3. Mount the UPS in the rack. Install the UPS at or near the bottom of the rack. 4. Reinstall the battery module. 4 5. Connect the battery and attach the front bezel. 6. Connect the equipment and power to the UPS. 7. Turn on the UPS. INSTALLING THE MOUNTING RAILS IN THE RACK Install the mounting rails in the rack. Directions are included with the rail kit. The UPS comes with standard 19-inch (46.5 cm) rack mounting rails, brackets, and cleats. The rack can have any of the common types of equipment mounting holes (square, round-threaded, or round-non-threaded). All necessary hardware is provided. REMOVING THE BATTERY MODULE The UPS is heavy. To lighten it, remove the battery module before mounting the unit in the rack. Due to its weight, two people are required to remove the battery module. The battery module is accessible from the front of the UPS (shown at left). This procedure requires a Phillips screwdriver. 1. If the UPS has been in operation, locate the white cord attached to the battery module connector plug . Grasp the cord and pull firmly toward you until the connector plug is disconnected. DO NOT pull the battery module cables. If the UPS has not been in operation, the battery will not yet be connected. The UPS ships with the battery disconnected. 2. Use a screwdriver to remove the two battery module mount screws located at the top corners of the face plate . Set the screws aside in a safe place. You will replace them later. 5 MOUNTING THE UPS IN THE RACK 3. Locate the battery module handle at the top of the battery face plate . 4. Be careful during this step.the battery module is heavy. Pull the battery module handle toward you to slide the battery module out of the UPS. DO NOT pull on the battery cables or the white cord. 1. Supporting the UPS on both sides, carefully align the unit with the rails. Use the handles on the side of the UPS to support the unit. 2. Each side of the UPS has a cleat that must slide into the groove on the rails. Insert each cleat into its groove and slide the UPS into position. 3. Use the four ornamental screws supplied with the UPS to attach the mounting brackets to the rack post. Insert the screws into the top and bottom holes in the U-space. REINSTALLING THE BATTERY MODULE 1. Supporting the battery module on the bottom, align it with the opening and slide the battery module into the compartment. 2. Replace the two screws to secure the battery module face plate. 6 Due to its weight, two people are required to install the UPS in the rack. a .snap. when the connector is seated properly. 3. Push the battery cables and white cord as close to the UPS as possible. 4. The UPS is shipped with the front bezel removed (it is packaged separately within the main box). Unpack the bezel and hold it with the cutout sec- tion on the right. Align the tabs on the side of the bezel with the slots on the front of the UPS and gently snap it into place. To connect an optional external battery pack(s) to the UPS, refer to the 3U Rack Mount External Battery Pack User.s Manual for instructions. a .snap. when the connector is seated properly. 3. Push the battery cables and white cord as close to the UPS as possible. 4. The UPS is shipped with the front bezel removed (it is packaged separately within the main box). Unpack the bezel and hold it with the cutout sec- tion on the right. Align the tabs on the side of the bezel with the slots on the front of the UPS and gently snap it into place. To connect an optional external battery pack(s) to the UPS, refer to the 3U Rack Mount External Battery Pack User.s Manual for instructions. CONNECTING THE BATTERY AND ATTACHING THE FRONT BEZEL 1. Facing the front of the UPS, locate the battery cables and the UPS battery connector jack . to the right of the battery module. 2. To connect the battery connector plug to the battery jack, push the plug into the jack so the metal pieces inside each part are touching. Press firmly to ensure a tight connection. You will hear CONNECTING POWER AND EQUIPMENT TO THE UPS 1. On the back panel, plug the UPS into a two-pole, three-wire, grounding receptacle only. Avoid using extension cords and adapter plugs. 2. Connect equipment to the UPS. Use the cable provided with your UPS to connect to the Computer Interface Port. DO NOT use a standard serial interface cable since it is incompatible with the UPS connector. 3. 120V Models only: Connect ground leads to the TVSS screw on the back panel. The transient voltage surge suppression (TVSS) screw provides grounding through the UPS power cord ground conductor. To make the co...
Questo manuale è adatto anche per i modelli :Alimentazione e alimentazione - 2200VA (449.42 kb)