valutazioni - 4, GPA: 3.5
(
)
)
|
Facilità d'uso
The UPS filters small utility line fluctuations and isolates electronic equipment from large disturbances by internally disconnecting from utility line power. The UPS providescontinuous power from the internal battery until utility power returns to safe levels or the battery is fullydischarged. Unpack Read the Safety Guide before installing the UPS. The User Manual and Safety Guide are accessible on the supplied User Manuals CD and on the APC Web site, Inspect the UPS upon receipt. Notify the carrier and dealer if there is damage. The packaging is recyclable; save it for reuse or dispose of it properly. Check the package contents: • UPS • Front bezel • Rail kit • EPO connector • UPS literature kit containing: – Two mounting brackets – Eight flathead screws – Product documentation – Smart-UPS® User Manuals CD – PowerChute® CD – Serial and USB communication cables – Safety information – Warranty information Specifications 230V Models Only: UPS literature kit additional contents: • Input power cord • Alternate input power cord (UK customers) • Utility connector plug • IEC jumper cables The model and serial numbers for all units are located on the rear panel. See the small label with numbers and bar codes. TemperatureOperatingStorage 32° to 104° F (0° to 40° C) 5° to 86° F (-15° to 30° C) charge the UPS battery every six months 86° to 113° F (30° to 45° C) charge the UPS battery every three months This unit is designed for indoor use only. Select a location sturdy enough to handle the weight. Do not operate the UPS where there is excessive dust or the temperature or humidity are outside the specified limits. Maximum Elevation OperatingStorage 10,000 ft (3,000 m) 50,000 ft (15,240 m) Humidity 0 to 95% relative humidity, non-condensing Weight 135 lbs (61 kg) with battery module 80 lbs (36 kg) without battery module 135 lbs (61 kg) Maximum Number of External Battery Packs Supported by the Smart-UPS XL 10 Smart-UPS XL 2200/3000 VA 120/230 VAC 3U Rack Mount User Manual 4 Smart-UPS XL 2200/3000 VA 120/230 VAC 3U Rack Mount User Manual Installation Installation Your UPS model may vary from the examples depicted in this manual. The UPS and the battery module are heavy. Remove the battery module to lighten the UPS during installation. Install the Rails in the Rack For details on rail installation refer to the instructions in the rail kit. Install the UPS in the Rack and Connect the Battery Module 4x 4x .. .. .. .. .. .. Smart-UPS XL 2200/3000 VA 120/230 VAC 3U Rack Mount User Manual 5 Start Up Accessories This UPS is equipped with an accessory SmartSlot. Refer to the APC Web site, for available accessories. If a standard accessory, such as a SNMP card is installed on this UPS, refer to the Utility CD for user documentation. Install accessories prior to connecting power to the UPS. Start Up Connect Equipment and Power to the UPS 1. The UPS features a transient voltage surge-suppression (TVSS) screw located on the rear panel, for connecting the ground lead on surge suppression devices such as telephone and network line protectors. Prior to connecting the grounding cable, ensure that the UPS is NOT connected to utility or battery power. 2. Connect equipment to the UPS. NOTE: This UPS is equiped with an external battery connector on the rear panel of the unit. Where appropriate use an APC extension battery cable. For ordering details contact your dealer or APC through the Web site 3. Add optional accessories to the SmartSlot located on the rear panel. 4. Plug the UPS into a two-pole, three-wire, grounded receptacle only. Avoid using extension cords. – 230 V models: The utility power cord is supplied in the UPS literature kit. Prior to connecting the utility power, connect the ground lead (optional) to the TVSS screw. 5. 120 V models: Check the SITE WIRING FAULT LED located on the rear panel. The LED will be illuminated if the UPS is plugged into an improperly wired utility power outlet, (see Troubleshooting). 6. To use the UPS as a master on/off switch be sure all connected equipment is switched on. Rear Panels 120 VAC 230 VAC Start Up Start the UPS 1. Press the button on the front panel to start the UPS. – The battery charges to 90% capacity during the first four hours of normal operation. Do not expect full battery run capability during this initial charge period. – Refer to the APC Web site, for battery runtimes. 2. For optimal computer system security, install PowerChute Smart-UPS monitoring software. Communication Ports SERIAL PORT USB PORT Use only the supplied cable to connect to the serial port. A standard serial interface cable is incompatible with the UPS. Serial and USB ports cannot be used simultaneously. Emergency Power Off The emergency power off (EPO) feature is user configurable. EPO provides immediate de-energizing ofconnected equipment from a remote location, without switching to battery operation. 1. Use the EPO connector supplied with the UPS. 2. Use a no...