valutazioni - 2, GPA: 4.5
(
)
)
|
Facilità d'uso
AT-MCF2000AC Power Supply Module Note For a list of available chassis models in the AT-MCF2000 media converter product line, contact your Allied Telesis sales representative or visit our web site. 1110-a NORMAL FAULT STATUS PSU FAN Review the following before you begin to install the module in the chassis: . Refer to the chassis’ Installation Guide to verify that the module is appropriate for the unit. . For instructions on how to remove a power supply module, refer to the chassis’s Installation Guide. . The AT-MCF2000AC power supply module is hot-swappable. You can install or replace the module while the chassis is powered on. . Refer to the chassis’ Installation Guide for a list of safety precautions to observe when installing the power supply module in the unit. . The following procedure uses the AT-MCF2000 media converter chassis for illustration purposes. Your chassis may be different. Package Contents Make sure the following items are included in the shipping package. If an item is missing or damaged, contact your Allied Telesis sales representative for assistance. . One AT-MCF2000AC power supply module . Four regional AC power cords . One power cord retaining clip . This Installation Guide Installing the AT-MCF2000AC Power Supply Module To install the AT-MCF2000AC power supply module, perform the following procedure: 1. Remove the power supply module from the shipping package. Store the packaging material in a safe location. You must use the original shipping material if you need to return the unit to Allied Telesis. 2. Remove a blank panel from a power supply/fan module slot on the back panel of the chassis by loosening the two captive screws of the panel with a cross-head screwdriver. Refer to the chassis’ Installation Guide for the location of the power supply/fan module slots. Figure 2. Removing the Blank Panel from a Power Supply/Fan Module Slot 3. Slide the power supply module into the slot as shown in Figure 3, until it is flush with the back panel of the chassis. Light pressure may be needed to seat the module on the connector on the back panel of the chassis. AT-MCF2KPNL2 AT-MCF2KPNL3 1111-a MA A Caution Do not force the module into place. Doing so may damage the connector pins on the backplane inside the chassis. Figure 3. Installing the AT-MCF2000AC Power Supply Module 4. Secure the power supply module to the chassis by tightening the two captive screws using a cross-head screwdriver. Refer to Figure 4. Figure 4. Securing the Power Supply Module 5. Locate the retaining brackets on either side of the AC power connector. Refer to Figure 5. Figure 5. Locating the Retaining Clip Brackets AT-MCF2KPNL3 NORMAL FAULT STATUS PSU FAN 1111-a MANAG A 1113-a AT-MCF2KPNL3 NORMAL FAULT STATUS PSU FAN M A AT-MCF2KPNL3 NORMAL FAULT STATUS PSU FAN M A Retaining Clip Brackets AT-MCF2000AC Power Supply Module Installation Guide Allied Telesis, Inc. 613-000575 Rev A 1 *613-000575 RevA* 2 3 6. Position the retaining clip as shown in Figure 6 and press the sides of the clip towards the center while inserting the short ends into the holes in the bracket. Figure 6. Installing the Retaining Clip Note If this is the initial installation of the chassis, refer to the chassis’ Installation Guide for instructions on how to install the remaining modules in the unit. Otherwise, continue with this procedure to apply power to the power supply module. 7. Verify that the power switch on the module is set to OFF. 8. Plug the appropriate power cord for your region or country into the AC power connector on the back panel of the unit and plug the other end into an appropriate power source. Refer to "Technical Specifications" for the power requirements of the power supply. Figure 7. Connecting the AC Power Cord 1114-a AT- MCF2KPNL3 NORMAL FAULT STATUS PSU FAN M A 1116-a AT-MCF2KPNL3 NORMAL FAULT STATUS PSU FAN M A 9. Lower the power cord retaining clip to secure the power cord to the chassis. Refer to Figure 8. This is to prevent the power cord from being inadvertently disconnected from the unit. Figure 8. Positioning the Power Cord Retaining Clip 10. Power on the AT-MCF2000AC module and the media converter chassis by setting the power switch to ON. AT-MCF2000AC Power Supply Module LED The power supply module has two LEDs. The states of the LEDs are defined in this table. Troubleshooting the AT-MCF2000AC Power Supply Module If you encounter a problem with the power supply module, try the following: . View the LEDs on the module to determine whether the module is operating normally. . Verify that the module is fully seated in the power supply/fan slot on the back panel of the chassis. . Verify that the power cord is firmly connected to the power supply module and the power source. . Verify that the power source is operating properly by plugging a different device into it. . Replace the power supply module with another power supply module. LED State Description PSU Off The power supply in the module is not rece...