valutazioni - 2, GPA: 4
(
)
)
|
Facilità d'uso
An unbalanced blade will cause excessive vibration when rotating at high speeds and may cause damage to the unit. The blade can be tested by balancing it on a round shaft screwdriver or nail. Remove metal from the heavy side until it balanced evenly. See figure 16. NOTE When reassembling, make certain the opening on the back-up plate is toward the bottom of the unit. The back-up plate may be reversed to provide a new cutting edge. 9 I When reassembling the blade, tighten to between 375 and 450 inch pounds, or lacking torque wrench, t ghten securely. FLAILS AND FINGERS The flails and fingers may be reversed wher they become dull. It is suggested that this procedure be performed by your nearest authorized service dealer. OFF-SEASON STORAGE If the shredder is to be inoperative for a period longer than 30 days, the following precautions are recommended. 1. Working outdoors, drain all fuel from the fu€ I tank. Run the engine until it stops from lack of fuel. A*-# J WARNING } DO NOT DRAIN FUEL WHILE SMOKING, OR IF NEAR AN OPEN FIRE. 2. Drain all the oil from the crankcase (this she uld be done after the engine has been operated anc is still warm) and refill crankcase with fresh oil. 3. Protect the inside of the engine for storage as follows. Remove spark plug, pour approximately 1/2 ounce (approximately one tablespoon) of engine oil into cylinder and crank slowly to distribute oil. Rsplace spark plug. 4. Clean the engine and the entire unit thoroughly. ■¡^ NOTE When storing any type of power equipment in an unventilated or metal storage shed, care should be taken to rustproof the equipment. Using a light oil or silicone, coat the equipment, especially all moving parts. 5. Store in a clean, dry area. 10 TROUBLE SHOOTING CHART SYMPTON POSSIBLE CAUSE(S) SOLUTION Engine fails to start 1. Check fuel tank for gas. 2. Spark plug lead wire disconnected. 3. Faulty spark plug. 1. Fill tank if empty. 2. Connect lead wire. 3. Clean, adjust gap or replace. Hard starting or loss of power 1. Spark plug wire loose. 2. Dirty air cleaner. 1. Connect and tighten spark plug wire. 2. Clean air cleaner as described in separate engine manual. Engine overheats 1. Carburetor not adjusted properly 2. Air flow restricted. 3. Engine oil level low. 1. Adjust carburetor. See maintenance separate engine manual. 2. Remove blower housing and clean as described in the separate engine manual. 3. Fill crankcase with the proper oil. Material not shredding Blade and/or flails not sharp. Sharpen or reverse blade and flails. Engine bogs down or stalls 1. No fuel in fuel tank. 2. Feeding, material into the machine too quickly. 1. Fill tank if empty. 2. Do not force material into the opening Feed gradually. NOTE: For repairs beyond the minor adjustments listed above, please contact your nearest authorized service. I 11 I Model 650 12 Model 650 PARTS LIST FOR MODEL 650 SHREDDER Ref. No. Part No. Color Code Description New Part Ref. No. Part No. Color Code Description New Part 1 11476 Door Chip It 31 714-0144 Cotter Pin 1/8" Dia. x 1.00" 2 710-0465 Hex Bolt 1/2-20 x 4.50" Lg* Lg* (Special) 3 711-0580 Clevis Pin 32 736-0192 Fl.-Wash. .531" I.D. x 937 4 711-0579 Flail Spacer 7/32'' Lg. O.D. x .09 5 11455 Cutting Finger 33 11459 Flail 6 736-0921 L-Wash. 1/2" I.D.* 34 711-0564 Flail Spacer 23/32" Lg. 7 726-0111 Palnut 3/16" Dia. 35 711-0578 Clevis Pin .50" Dia. x 3.0" Lg. 8 712-0922 Hex Jam Nut 1/2-20 Thd* 36 736-0247 Fl.-Wash. .406" I.D. x 1.25" 9 714-0507 Cotter Pin 3/32" Dia. x 3/4" O.D. Hdn. Lg- 37 736-0217 L-Wash. 3/8" I.D. H.D. 10 16568 Chute Deflector N 38 710-0151 Hex Bolt 3/8-24 x 2.0" Lg. H.T. 11 712-0107 L.-Nut 1/4-20 Thd. 39 14575-463 Flail Housing Ass'y.-Comp. 12 710-0289 Hex Bolt 1/4-20 x .50" Lg* 40 732-0546 Torsion Spring .062 Dia. x 1.06 N 13 714-0114 Sq. Key 1/4" x 2.00" Lg. Lg- 14 13430 Impeller Assembly 41 11477 Chip-lt Guide Ass'y- 15 710-0157 Hex Bolt 5/16-24 x 3/4" Lg. 42 11478 Hinge Pin 16 736-0119 L.-Wash. 5/16" I.D.* 43 747-0531 Release Bar N 17 14573 Hopper to Engine Mtg. Plate 44 712-0109 Wing Nut Elastic 1/4-20 Thd. 18 Engine 45 13431 Blade 19 11464 Engine Mounting Plate 46 11460-463 Upper Leaf Ramp Section 20 712-0123 Hex Nut 5/16-24 Thd* 47 16524-463 Lower Leaf Ramp Section N 21 736-0119 L.-Wash. 5/16" I.D.* 48 736-0264 Fl.-Wash. 5/16" I.D. 22 738-0521 Shaft 49 11481-463 Hopper Assembly 23 736-0170 Special L.-Wash. 5/16" I.D. 50 710-0601 Hex Wash. Hd. Self-Tap Scr. 24 726-0221 Push Cap 5/16-18 x .75" Lg. 25 711-0494 Spacer 52 11454 Back-Up Plate 26 734-1056 Wheel Ass'y.-Comp. 53 16522 Inlet Guide Assembly N 27 736-0100 Fl.-Wash. .50" I.D. 55 11480 Stop Washer 28 710-0624 Hex Bolt 5/16-24 x 1.50" Lg* 56 710-0542 Hex Bolt 5/16-18 x 8.38" Lg. 29 712-0429 Elastic Lock Nut 5/16-18 Thd. 57 735-0639 Spark Plug Elbow (Optional) 30 710-0237 He...