Avoid wearing loose fitting clothing. 3. This machine should be operated only upon an earthen level surface. 4. Assure that all screws, nuts and bolts and other fasteners are properly secured. OPERATION 1. When feeding shreddable material into this equipment, be extremely careful that pieces of metal, rocks, bottles, cans or other foreign objects are not included. 2. If the cutting mechanism strikes any foreign object or if your machine should start making an unusual noise or vibration, imm

See figure 5. 6. Place upper guide extension in place on guide extension. Secure with four hex screws (B) and hex center lock nuts (C). A 7/16" wrench and adjustable wrench are required. See figure 5. FIGURE 5 5 OPERATION BEFORE STARTING ENGINE 1. Fill fuel tank with fresh regular gasoline. Do Not mix oil with gasoline. 2. Fill crankcase with oil. Refer to separate engine manual packed with your shredder. TO START ENGINE Tecumseh Engine 1. Place control lever (on engine) in "RUN1 posit

5/16" Scr.* 42 11478 Hinge Pin 17 14573 Hopper to Engine Mtg. Plate 43 726-0111 Palnut 3/16" Dia. 18 Engine 44 712-0109 Wing Nut Elastic 1/4-20 Thd. 19 11464 Engine Mounting Plate 45 13431 Blade 20 712-0123 Hex Nut 5/16-24 Thd:* 46 11460-488 Guide Extension Assembly 21 736-0119 L.-Wash. 5/16" Scr.* 47 11472-488 Guide Extension 22 738-0521 Shaft 48 736-0264 FI.-Wash. 5/16" Scr.* N 49 11481-488 Hopper Assembly 23 736-0170 Special L.-Wash. 5/16" I.D. 50 7

No. 11). See page 10. 2. Remove bolt (Ref. No. 38), lock washer (Ref. No. 37) flat washer (Ref. No. 36) which holds blade (Ref. No. 45), and blade retainer (Ref. No. 48) to engine crankshaft. See page 10. NOTE Blade is reversible and can be assembled to crankshaft with either side showing. When sharpening blade, follow the original angle of grind as a guide. It is extremely important that each cutting edge receives an equal amount of grinding to prevent an unbalanced blade. An unbalanced bla

247.776350 Sears, Roebuck And Co., Hoffman Estates, IL 60179 U.S.A. Printed in U.S.A. CAUTION: Before using this product, read this manual and follow all safety rules and operating instructions. • Safety • Operation • Maintenance • Storage • Espanol, p. 29 Visit our website: FORM NO. 769-00831A.fm (4/2004) For answers to your questions about this product, call: 1-800-659-5917 Sears Craftsman Help Line (5 am. - 5 pm., Mon. - Sat.) TABLE OF CONTENTS TABLE OF CONTENTS Content Page Content Page Warr

THIS WARRANTY APPLIES ONLY WHILE THIS PRODUCT IS IN USE IN THE UNITED STATES. This warranty gives you specific legal rights, and you may also have other rights which vary from state to state. Sears, Roebuck and Co., D/817WA, Hoffman Estates, II 60179 ACCESSORIES These accessories are available where the unit was purchased. They are also available at most Sears retail outlets, and service centers. Most Sears stores can order repair parts for you when you provide the model number of your Crafts

If a spark arrester is used, it should be maintained in effective working order by the operator. In the State of California the above is required by law (Section 4442 of the California Public Resources Code). Other states may have similar laws. Federal laws apply on federal lands. A spark arrester for the muffler is available through your nearest engine authorized service dealer or contact the service department, P.O. Box 361131 Cleveland, Ohio 44136-0019. FORM NO. 770-10048J PRINTED IN U.S.A. 5