valutazioni - 2, GPA: 4
(
)
)
|
Facilità d'uso
B C D E F G H I J L M K N O * A A. 18" (45.7 cm) upper cabinet to countertop B. 22" (55.9 cm) C. Junction box to be located in this shaded area D. 4" (10.2 cm) E. 20" (50.8 cm) F. 12" (30.5 cm) G. 5." (14 cm) H. Gas line opening to be located in this shaded area I. 3." (8.9 cm) J. 8" (20.3 cm) K. 30." (76.8 cm) L. 4" (10.2 cm) min. clearance from both sides of range to side wall or other combustible material M. For minimum clearance to top of range, see NOTE*. N. 30" (76.2 cm) min. upper cabinet width O. 13" (33 cm) max. upper cabinet depth *NOTE: 36" (91.4 cm) minimum when bottom of wood or metal cabinet is protected by not less than ..." (0.64 cm) flame retardant millboard covered with not less than No. 28 MSG sheet steel, 0.015" (0.4 mm) stainless steel, 0.024" (0.6 mm) aluminum or 0.020" (0.5 mm) copper. 42" (106.7 cm) minimum clearance between the top of the cooking platform and the bottom of an unprotected wood or metal cabinet. If installing a hood above the range, follow the hood instructions for dimensional clearances above the cooktop surface. ElectricalRequirements -U.S.A.Only If codes permit and a separate ground wire is used, it is recommended that a qualified electrical installer determine that the ground path and wire gauge are in accordance with local codes and that the ground path is adequate. Do not use an extension cord. Make sure that the electrical connection and wire size are adequate and in conformance with the National Electrical Code, ANSI/NFPA 70-latest edition and all local codes and ordinances. A copy of the above code standards can be obtained from: National Fire Protection Association, One Batterymarch Park, Quincy, MA 02269 Electrical Connection To properly install your range, you must determine the type of electrical connection you will be using and follow the instructions provided for it here. ¦ Do not ground to a gas pipe. ¦ Check with a qualified electrical installer if you are not sure the range is properly grounded. ¦ Do not have a fuse in the neutral or ground circuit. ¦ Range must be connected to the proper electrical voltage and frequency as specified on the model/serial number rating plate. (The model/serial number rating plate is located on the right vertical surface of the oven door frame.) ¦ Range must be connected to a grounded metal, permanent wiring system. ¦ A 4-wire or 3-wire, single phase, 120/240 volt, 60 Hz., AC only electrical supply is required on a separate, 30-amp circuit, fused on both sides of the line. ¦ A time-delay fuse or circuit breaker is recommended. The fuse size must not exceed the circuit rating of the range specified on the model/serial rating plate located on the right vertical surface of the oven door frame. ¦ The range can be connected directly to the fused disconnect (or circuit breaker box) through flexible, or nonmetallic sheathed, copper or aluminum cable. The flexible cable extending from the fuse box or circuit breaker box should be connected directly to the junction box. See “Make Electrical Connection.” ¦ Locate the junction box to allow as much slack as possible between the junction box and the range so that the range can be moved if servicing is ever necessary. Do not cut the conduit. ¦ A UL listed conduit connector must be provided at each end of the power supply cable (at the range and at the junction box). ¦ Wire sizes and connections must conform with the rating of the range (30 amps). ¦ If the house has aluminum wiring, follow the procedure below: a) Connect the aluminum wiring to the copper wiring using special connectors designed and UL listed for joining copper to aluminum. Follow the electrical connector manufacturer’s recommended procedure. b) Aluminum/copper connection must conform with local codes and industry-accepted wiring practices. ElectricalRequirements -CanadaOnly If codes permit and a separate ground wire is used, it is recommended that a qualified electrical installer determine that the ground path and wire gauge are in accordance with local codes. Be sure that the electrical connection and wire size are adequate and in conformance with the CSA Standard C22.1, Canadian Electrical Code, Part 1 - latest edition, and all local codes and ordinances. A copy of the above code standards can be obtained from: Canadian Standards Association 178 Rexdale Blvd. Toronto, ON M9W 1R3 CANADA. ¦ Do not ground to a gas pipe. ¦ Check with a qualified electrical installer if you are not sure the range is properly grounded. ¦ Do not have a fuse in the neutral or ground circuit. ¦ When a 4-wire, single phase 208/240 volt, 60 Hz., AC only electrical supply is available, a 30-amp minimum circuit protection is required, fused on both sides of the line. ¦ A time-delay fuse or circuit breaker is recommended. The fuse size must not exceed the circuit rating of the range specified on the model/serial rating plate located on the right vertical surface of the oven door frame. GasSupply Requirements WARNING Explosion Hazard Use a new CSA...