valutazioni - 5, GPA: 3.6
(
)
)
|
Facilità d'uso
1/3/01 ITEM QTY. WRO1075 107442 WR00919 WR00022 WRO10931 106461 106579 WR50263 WRO1092 WR50243 WR50251 WR5I084 WR510851 PART NO. SKEWER ASSEMBLY. WELDMENT KIT ASSEMBLY. DRAIN - ROTISSERIE STAND STAND ASEMBLY (CBS32) RACK. ANTI-SPLASH PANEL ASSEM8LY. RIGHT SIDE. PAINTED CORD ASSEMBLY. 3-WIRE. ELEC. BUSHING. STRAIN RELIEF (HEYCO 1200) CIRCUIT BREAKER. 1.8 AMP PANEL ASSEMBLY. BACK BOOY COVER. VENT. TOP VENT SEAL PANEL. TOP BODY PANEL. LEFT SIDE. PAINTED DESCRIPTION CLEVELAND RANGE INC. 1333 Eut I79lh St. CUvtltnd. Ohio 441IO-25M BOSTON MARKET ROTISSERIE STAND AND OUTER SHEETING ASY00I BMR-32 Rôtisserie Oven i BMR-32 Rôtisserie Oven BMR-32 Rôtisserie Oven BMR-3? Rôtisserie Oven_- 1-11 bVL --UdA(J dUdbbl+UH ¿b-yyyb 1-14- Cleveland Range Inc. Gear Drive Assembly ASY007 This drawing shows exploded views of the rotis-serie drive system, along with various assembly details of the axle and drums, the sun and planetary gears, and the motor drive system. The axle (#4) turns in two bearings (#31) mounted to each side wall; note the gaskets (#33) used to seal the bearings. The idler and drive end drums (#2 and #8) are axially aligned with the axle by means of hub slots that engage with spring pins ((#3) pressed through the axle. The drums are then secured to the afxle by cap screws (#1) that engage a flat machined into the axle (see also details A and B). These cap screws are specially machined and plated for this purpose -DO NOT SUBSTITUTE. The drums occasionally may need to be moved inwards on the axle when cleaning the oven. When returning the drums to proper position, make sure the cap screws line up with the flats on the axle, and the slots in the hubs engage the spring pins before tightening the cap screws. Also, when returning the drive end drum assembly to position, rotationally jog the drum so the planetary gears (#10) mesh with the sun gear (#13; see detail C), then engage the hub with the right-hand spring pin. No lubrication is required for the sun and planetary gears. Special tapered-cone bushings (#25, 0.750-inch shaft, and #27, 1.000-inch shaft) are used to secure the drive pulleys (#24 and #28) to the gearmotor shaft (#18) and the rotisserie axle (#4). The bushing is assembled to the shaft using a keyed/slot and set screw (screw "hand tight" only). The pulleys are then slid over the tapered bushing cones (all cone surfaces must be clean and dry). When assembling, align the through-drilled bolt holes in the pulley with the drilled-and-tapped holes in the bushing. Pull-up bolts (with lock washers) are then inserted through the pulley's drilled holes, threaded into the bushing's tapped holes, and tightened alternately and evenly to the following torques: a) the smaller, 0.750 shaft: 108 in-lbs.; b) the larger, 1.000-inch shaft: Cone Bushing Key and Set Screw Motor Shaft (or Rotor Axle) Pulley P Pull-up Bolts and Lock Washers (note torque specs.) rHJi 360 in-lbs. (To remove the pulleys, the pull-up bolts must be removed and threaded into the pulley's tapped holes and brought to bear on the bushing's flange. The cone grip is then broken by alternately tightening the bolts.) Adjust the tension of the drive belt (#26) so that you can twist the belt, by hand, no more than half a twist. Tension is adjusted by sliding the motor support bracket in its slots and tightening the hex nuts (#21). BMR-32 Sen/»™* Manual BMR-32 Rôtisserie Oven - 1-15 BMR-32 Rôtisserie Oven - 1-17 28 27 26 25 24 23 22 21 20 19 17 16 15 14 13 12 1 1 10 ITEM