valutazioni - 2, GPA: 4.5
(
)
)
|
Facilità d'uso
Setting the oven control to the desired time outputs voltage, through a reversing switch, to the conveyor motor. NOTE: The conveyor system uses a hall effect sensor and magnet to prove operation of the conveyor motor. If the conveyor motor is not running, “BELT JAM” is indicated on the display. AUTOMATIC COOL DOWN When the oven is started, the time delay relay timing circuit is enabled, permitting the oven fans to run approximately 20 minutes after the oven is shut off, to cool the oven. The time delay relay will keep the coil of the fan relay closed, maintaining operation of the main fan and cooling fans. Impinger II – Advantage Digital Express Service Manual - Domestic SCHEMATIC DIAGRAM MODEL 1116-080-A, 1116-080-A1, 1117-080-A, 1117-080-A1 Impinger II – Advantage Digital Express Service Manual - Domestic SCHEMATIC DIAGRAM MODEL 1130-080-A, 1130-080-A1, 1131-080-A, 1131-080-A1 SCHEMATIC DIAGRAM Impinger II – Advantage Digital Express Service Manual - Domestic MODEL 1132-080-A, 1132-080-A1, 1133-080-A, 1133-080-A1 Impinger II – Advantage Digital Express Service Manual - Domestic SCHEMATIC DIAGRAM MODEL 1161-080-A Impinger II – Advantage Digital Express Service Manual - Domestic SCHEMATIC DIAGRAM MODEL 1162-080-A Impinger II – Advantage Digital Express Service Manual - Domestic SCHEMATIC DIAGRAM MODEL 1130-08H-A, 1131-08H-A Impinger II – Advantage Digital Express Service Manual - Domestic SCHEMATIC DIAGRAM MODEL 1132-08H-A, 1133-08H-A Impinger II – Advantage Digital Express Service Manual - Domestic TROUBLESHOOTING GUIDE GAS OVENS MODEL 1116-080-A MODEL 1116-080-A1 MODEL 1117-080-A MODEL 1117-080-A1 NAT. GAS NAT. GAS LP GAS LP GAS 120VAC 120VAC 120VAC 120VAC 60 HZ. 60 HZ. 60 HZ. 60 HZ. SYMPTOM POSSIBLE CAUSE EVALUATION Oven fan will not run Incoming power supply Check circuit breakers, reset if required. Check power plug to be sure it is firmly in receptacle. Measure incoming power, call power co. if needed. Fuse, 10 Amp Check, replace if necessary. Fuse holder Check, replace if necessary. Hi-limit thermostat, control box Check for voltage on both sides of switch. Terminals are normally closed. If open, reset and test oven for proper operation. If thermostat will not hold, and control box temperature is not exceeding 140°F (60°C), replace thermostat. Switch, main power Check continuity between switch terminals. Replace switch as needed. Main fan motor Check for 120VAC at motor. If no voltage is present, trace wiring back to main power switch. WITH POWER OFF: Check for opens, shorts or grounds. Turn fan blade to check for locked rotor. Capacitor Check for shorts or grounds. WARNING: Capacitor has a stored charge, discharge before testing. No control box cooling Incoming power Check circuit breakers, reset if required. Check power plug to be sure it is firmly in receptacle. Measure incoming power, call power co. if needed. Switch, main power Check continuity between switch terminals. Replace switch as needed. Cooling fan Check for 120VAC at cooling fan. If no voltage is present, trace wiring back to power switch. If voltage is present, and motor does not run, check for...
Questo manuale è adatto anche per i modelli :Forni elettrici - 1116-080-A (1.17 mb)
Forni elettrici - 1116-080-A1 (1.17 mb)
Forni elettrici - 1117-080-A1 (1.17 mb)
Forni elettrici - 1130-080-A (1.17 mb)