valutazioni - 3, GPA: 4
(
)
)
|
Facilità d'uso
2 Refer to the following pages for important information regarding the installation of LCS and LCG ClimaPlus Combis. It is recommended that installation be accomplished by a certified and properly trained technician. NOTE: When installing a ClimaPlus combi, humidity calibration must be performed. This process takes approximately 45-60 minutes. (page 62) Site, leveling Minimum clearance sides and back: 2 in. (50 mm) Service clearance, left side: 20 in. (500 mm) Clearance for door opening: Model 6 & 10: 201.2 in. (521 mm) Model 1020: 291.2 in. (749 mm) Model 20: 283.4 in. (730 mm) Model 40: 303.4 in. (781 mm) 1) Check for any transport damages. Should there be any signs of transport damage immediately inform your dealer/freight forwarder. 2) Check installation site. Check entrance clearance. Minimum entrance space needed without pallet: Model 6 & 10: 351.2 in. (902 mm) Model 1020: 495.8 in. (1262 mm) Model 20: 397.8 in. (1012 mm) Model 40: 521.2 in. (1332 mm) Floor at installation site must be level. Cold water line in place. (page 63) 2 in. (50 mm) drain connection installed. Max. drain height for floor units: 4 in. (100mm) Electrical power supply/protective measures installed and sized correctly. (page 60-61) 3) Remove all cartons, packing materials, documents etc. from the interior cabinet. 4) Remove grid shelves/trolley from cabinet. 5) Take unit off the pallet. Moving unit without pallet: Sizes 6, 10, 1020 (Fig. 1) Moving unit without pallet: Sizes 20, 40 (Fig. 2) 60 Unit weights: LCS 6: 270 lbs. (123 kg) LCG 6 335 lbs. (152 kg) LCS 10 334 lbs. (152kg) LCG 10 384 lbs. (174 kg) LCS 1020 484 lbs. (220 kg) LCG 1020 584 lbs. (265 kg) LCS 20 686 lbs. (312 kg) LCG 20 798 lbs. (362 kg LCS 40 972 lbs. (442 kg) LCG 40 888 lbs. (403 kg) 6) Installation models 6, 10, 1020 Place floor stand at the installation place and level by adjusting legs. (Fig. 3). Minimum clearance required to neighboring equipment or walls. (page 59) Place the unit on top of the stand. The unit’s legs must be centered on the locating pins of the stand (Fig. 4). Unit must be level (Fig. 5). 7) Installation models 20, 40 The unit must be secured against shifting on the floor by means of floor fixtures (Fig. 6). If floor fixtures are glued to the floor (use polyurethane glue or similar), remove all grease from the floor first. Place the unit at its final location and level by adjusting legs. (Fig. 5). Minimum clearance required to neighboring equipment or walls. (page 59) The area of floor under the unit where Mobile Oven Racks will roll in must be level or door will not seal. (Fig. 7). Electrical 8) Electrical connection Connect the unit only according to the information given on the data plate. Observe all regulations of your local Electrical Code. The appliance may only be connected by a licensed electrician. Each appliance requires an independent fused power supply line. Connection via GFI circuit breaker is advisable. On-site installation: provide accessible all-pole disconnection device with minimum of 1.8 in. (3 mm) contact gap (not required for 120v gas units.) Connect appliance to ground. Special voltages on request. Circuit diagram is located behind the operator panel. Connected load for electric units: INSTALLATION continued Model KW Amps 208v 3Phase 240v 3 Phase 208v 1 Phase 240v 1 Phase LCS-6 10 28 24 48 42 LCS-10 19 53 45.8 LCS-1020 31.5 87.5 75.9 LCS-20 38 105.6 91.5 LCS-40 63 175.1 151.8 Fig. 3 Fig. 4 Fig. 5 Fig. 6 Fig. 7 INSTALLATION L 1 L 2 L 3 N Fig. 8 Fig. 10 Fig. 9 240 volt tap Fig. 11 Cable Inlet Jumper wire Terminal location K3.1 relay Electrical requirements of gas units: Model Voltage Phase Cycle/Hz KW LCG-6 120 1 60 1 LCG-10 120 1 60 1 LCG-1020 208/240 1 60 1.5 LCG-20 208/240 1 60 1.6 LCG-40 208/240 3 60 3.5 Choose conductor size according above tables and your local regulations. IMPORTANT Gas units are voltage specific. Supply voltage must match voltage rated on data plate...
Questo manuale è adatto anche per i modelli :Forni elettrici - 6 (227.64 kb)
Forni elettrici - 6 (227.64 kb)
Forni elettrici - 6 (227.64 kb)