valutazioni - , GPA:
(
)
)
Produttore : Panasonic
File Size : 390.73 kb
File Nome : ES8078.PDF
Lingua di insegnamento: 
Il documento viene caricato, si prega di attendere
 |
Il documento viene caricato, si prega di attendere
Facilità d'uso
Failure to observe this may cause electric shock or result in short circuits. 1. Detach the shaver and the appliance plug from the self-cleaning recharger. 2. Fill the water tank with water. 1) Remove the water tank from the self-cleaning recharger (see fig. 10-1). 2) Open the water tank cap (see fig. 10-2). 3) Wash away the old cleaning liquid inside the water tank and rinse (see fig. 11). 4) Pour tap water up until feed water line (12). * Do not pour water over the water feed line in the tank. This may cause the cleaning liquid to spill. 3. Firmly shut the water tank cap and attach the tank to the self-cleaning recharger (see fig. 13). 4. Peel off the seals from the new detergent cartridge (two seals) (see fig. 14). • Hold the detergent cartridge horizontally. (The detergent may spill if tilted excessively.) 5. Attach the detergent cartridge to the self-cleaning recharger (see fig. 15). • Do not use any solution other than the Panasonic Shaver self-cleaning recharger special detergent. • Be sure to change the detergent cartridge and the cleaning liquid inside the water tank simultaneously. Adding water, or changing just the detergent cartridge or the water, will result in deteriorated cleaning functions. • When the self-cleaning recharger is operated, the concentrated detergent inside the cartridge will be diluted and the water inside the tank will become a cleaning liquid. Cleaning your shaver 1. Insert the appliance plug into self-cleaning recharger socket (see fig. 16-1). 2. Firmly insert the adaptor into AC outlet (see fig. 16-2). 11 3. Pull up the arm of the self-cleaning recharger until it clicks (see fig. 17-3). 4. Remove the protective cap and set the shaver firmly onto the self-cleaning recharger until it clicks (see fig. 17-4). • Ensure that the outer foil does not get deformed or damaged during setting. • Before using the self-cleaning recharger, make sure the shaver has been rinsed thoroughly with water if it has been washed with hand soap or any other detergent, and swish water off properly before setting the shaver into the self-cleaning recharger unit. The presence of soap or any other detergent residue will contaminate the cleaning solution in the self-cleaning recharger unit and could lead to poor cleaning performance. 5. To clean the shaver, select either the (Clean/Dry/Charge) course or the (Clean/Dry) course. To dry the shaver after rinsing, select the (Dry/Charge) course or the (Dry) course (see fig. 18). • The (Charge) course will begin immediately when the shaver is set onto the self-cleaning recharger. • A total of five courses are available. The display will alternate between (Clean/Dry/Charge) > (Clean/Dry) > (Dry/Charge) > (Dry) > (Charge) whenever the select button is pressed. • The course will start approximately six seconds after being selected. * Press the select button within six seconds to choose a different course (see fig. 3). WARNING – Do not remove the shaver from the self-cleaning recharger when courses that include the (Dry) function are in use. A heater is used during the drying process, and this may result in the area around the blade becoming extremely hot and causing burns. The course will be aborted if the power is cut off during cleaning. In this event, it is necessary to perform the (Clean/Dry/Charge) or (Clean/ Dry) course once again from the beginning. It will take about 3 hours to finish the (Clean/Dry/Charge) or (Clean/Dry) course. The clean and dry lamp will blink after the (Clean/Dry/Charge) or (Clean/Dry) course is completed. • The self-cleaning recharger is mainly designed to clean the blades (outer foil and inner blades). Areas that are not soaked into the cleaning liquid or around the surface of the liquid are not subject cleaning. Carry out brush cleaning or wash with water to remove beard trimmings in these areas. 12 Replacing the Detergent Cartridge Replace the HydraClean ™ Shaving System Solution Cartridge when it has reached the end of its service life. Normally, it is recommended to replace it every 30-40 days if used once every day. Use the below chart as a guide. Note: In order to maintain maximum cleaning performance, it is important to replace the water in the water tank at the same time you replace the cartridge. Shaving Cleaning Reusability 1 time/day approx. 30~40 times 1 time/day 1 time/3 days approx. 10~15 times 1 time/1week approx. 4~7 times It is recommended to clean the shaver with the self-cleaning recharger after every shave. Change the cartridges when the status lamp is illuminated. Before exchange, make sure to inspect the cartridges with following procedure. Checking the status lamp In cases when the status lamp blinks, carry out the following inspections. 1. Is the detergent cartridge set properly? > Properly set the detergent cartridge (see fig. 15). 2. Was the detergent cartridge detached during cleaning? > Reset the detergent cartridge. After completing inspection • Properly set the detergent to extinguish the start each co...