Log:
valutazioni - 3, GPA: 4.7 ( )

Istruzioni per l'uso Gillette, Modello BRAUN 390CC

Produttore : Gillette
File Size : 6.42 mb
File Nome :
Lingua di insegnamento: en
Vai a scaricare



Facilità d'uso


Remove the shaver Foil & Cutter cassette and tap it out on a flat surface. • Using a brush, clean the inner area of the shaver head. However, do not clean the shaver Foil & Cutter cassette with a brush as this may damage it. Replacement light for shaving parts/Reset (390cc only) To maintain 100% shaving performance, replace the shaver Foil & Cutter cassette (1), when the replacement light for shaving parts (8) comes on (after about 18 months) or when worn. The replacement light will remind you during the next 7 shaves to replace the foil and cutter cassette. Then the shaver will automatically reset. After you have replaced the Foil & Cutter cassette (1), press the on/off switch (4) for at least 5 seconds to reset the counter. While doing so, the replacement light blinks and goes off when the reset is complete. The manual reset can be done at any time. Model 350cc: To maintain 100% shaving performance, replace the shaver Foil & Cutter cassette (1), at least every 18 months or when worn. Preserving the batteries In order to maintain the optimum capacity of the rechargeable batteries, the shaver has to be fully discharged (by shaving) every 6 months approximately. Then recharge the shaver to full capacity. Environmental notice This product contains rechargeable batteries. In the interest of protecting the environment, please do not dispose of the product in the household waste at the end of its useful life. Disposal can take place at a Braun Service Centre or at appropriate collection sites provided in your country. C Clean&Renew™ Braun Clean&Renew™ has been developed for cleaning, charging and storing your shaver. Clean your shaver daily in the Clean&Renew™. During the automated cleaning process, the shaver is switched on and off at intervals to obtain best cleaning results. Since the specially formulated cleaning fluid contains a small amount of oil, the cleaning procedure also fulfils the lubrication needs of the shaver. Important • Only use the power supply cord set supplied with the shaver. • In order to avoid any leakage of the cleaning fluid, place the appliance on a flat, stable surface. Do not tip, move suddenly or transport in any way if a cleaning cartridge is installed. • Do not place the appliance in a mirror cabinet, nor store it over radiators, nor place it on polished or lacquered surfaces. Do not expose to direct sunlight. • The appliance contains highly flammable liquid. Keep it away from sources of ignition. No smoking. • Keep out of reach of children. Do not refill cartridge. Use only original Braun refill cartridge. Description 1 Start/release button 2 Contact bow 3 Lift button for cartridge exchange 4 Level indicator 5 Cleaning cartridge Before using Clean&Renew™ Installing the cartridge • Press the lift button (3) to open the housing. • Hold the cartridge down on a flat, stable surface (e.g. table). Carefully remove the lid from the cartridge. Slide the cartridge into the base as far as it will go. • Slowly close the housing by pushing it down until it locks. Replacing the cartridge After having pressed the lift button to open the housing, wait for a few seconds before removing the used cartridge. Before discarding the used cartridge, make sure to close the openings using the lid of the new cartridge, since the used cartridge will contain contaminated cleaning solution. The used cartridge can be disposed in the household waste. Operating your Clean&Renew™ • Connect your Clean&Renew™ with the cord set to the mains electricity supply. The special socket at the back is adjustable to save space. After each shave, switch the shaver off and put it into the Clean&Renew™, upside down and with the front showing. • Push the start/release button (1) to lock and connect the shaver. The cleaning process will start. The yellow light on the shaver will flash during the complete process (approx. 2 minutes cleaning, min. 4 hours drying). • Do not interrupt the cleaning process, as it leaves the shaver wet and not fit for use. If interruption is needed nonetheless, press the start/release button (1). • When cleaning is finished, the yellow light will go off and the shaver is ready for use. To release it, push the start/release button. • A cleaning cartridge should be sufficient for about 30 cleaning cycles. When the level indicator (4) has reached the «min» mark, the remaining fluid in the cartridge is sufficient for about 5 more cleaning cycles. Then the cartridge should be replaced, when used daily approx. every 4 weeks. • The hygienic cleaning solution cartridge contains alcohol which, once opened, will naturally evaporate slowly into the surrounding air. Each cartridge, if not used daily should be replaced after approx. 8 weeks. • The cleaning cartridge also contains lubricates, which may leave residual marks on the shaver head after cleaning. However, these marks can be removed easily by wiping gently with a cloth or soft tissue paper. • Clean the housing from time to time with a damp cloth, especial...

Questo manuale è adatto anche per i modelli :
Elettrico - BRAUN 350CC (6.42 mb)

Scrivi la tua opinione del dispositivo



Il messaggio
Il tuo nome :
Inserire le due cifre :
capcha





categorie