valutazioni - 4, GPA: 3.8
(
)
)
|
Facilità d'uso
Follow safety messages to avoid or reduce the risk of injury or death. The manufacturer cannot possibly anticipate every possible circumstance that might involve a hazard.The warnings in this manual, and the tags and decals affixed to the unit are, therefore, not all-inclusive. If you use a procedure, work method or operating technique that the manufacturer does not specifically recommend, you must satisfy yourself that it is safe for you and others.You must also make sure that the procedure, work method or operating technique that you choose does not render the transfer switch unsafe. WARNING Only qualified electricians should attempt installation of this system, which must strictly comply with applicable codes, standards and regulations. • Failure to follow above warning could cause personal injury, damage and/or malfunction of equipment. Low voltage wire cannot be installed in same conduit as power voltage wiring. WARNING • • • • • • DO NOT touch bare wires or receptacles. DO NOT use transfer switch with worn, frayed, bare or otherwise damaged wiring. DO NOT handle electrical cords while standing in water, while barefoot, or while hands or feet are wet. If you must work around a unit while it is operating, stand on an insulated dry surface to reduce shock hazard. DO NOT allow unqualified persons or children to operate or service transfer switch. In case of an accident caused by electrical shock, immediately shut down the source of electrical power and contact local authorities. Avoid direct contact with the victim. Failure to properly ground transfer switch can result in electrocution. WARNING • Despite the safe design of the transfer switch, operating this equipment imprudently, neglecting its maintenance or being careless can cause possible injury or death. Transfer Switch contains high voltage that can cause personal injury or death. WARNING CAUTION Improper treatment of transfer switch can damage it and shorten its life. • • • • • Use transfer switch only for intended uses. If you have questions about intended use, ask dealer or contact Briggs and Stratton Power Products. DO NOT expose transfer switch to excessive moisture, dust, dirt, or corrosive vapors. Remain alert at all times while working on this equipment. NEVER work on the equipment when you are physically or mentally fatigued. If connected devices overheat, turn them off and turn off their circuit breaker/fuse. 3 Briggs & Stratton Power Products Automatic Transfer Switch Installation and Owner’s Manual INTRODUCTION Thank you for your purchase of this Briggs & Stratton Power Products Automatic Transfer Switch.This product is intended for use with Briggs & Stratton Home Standby Generator sets ONLY.This is an optional home standby system which provides an alternate source of electric power and to serve loads such as a gas furnace, refrigeration and communication systems that, when stopped during any power outage, could cause discomfort, or the like.This product DOES NOT qualify for emergency standby as defined by NFPA 70 (NEC). Briggs and Stratton Power Products (BSPP) has made every effort to provide for a safe, streamlined and cost-effective installation. Each installation is unique, it is impossible to know of and advise of all conceivable procedures and methods by which installation might be achieved.We do not know all possible hazards and/or the results of each method or procedure. For these reasons, Only licensed electrical contractors should install transfer switches. Installations must strictly comply with all applicable federal, state and local codes, standards and regulations. Your BSPP Transfer Switch is supplied with this combined “Installation and Owner’s Manual”.This is an important document and should be retained by the owner after the installation has been completed. Every effort has been expended to make sure that the information in this manual is both accurate and current. However, the manufacturer reserves the right to change, alter or otherwise improve the system at any time without prior notice. For the Home Owner To help you make informed choices and communicate effectively with your installation contractor(s), Read and understand the Owner Orientation Section of this manual BEFORE contracting or starting your transfer switch installation. To arrange for proper installation, contact the store at which you purchased your BSPP Transfer Switch, your dealer, or your utility power provider. The Transfer Switch Warranty is VOID unless the system is installed by a licensed electrical professional. For the Installing Dealer/Contractor Check federal, state and local codes for questions on installation. If you need more information about the transfer switch, call 1-800-743-4115, between 8:00 AM and 5:00 PM CT. Owner Orientation The illustrations are for typical circumstances and are meant to familiarize you with the installation options available with your transfer switch. Local codes, appearance, and distances are the factors that...
Questo manuale è adatto anche per i modelli :Energia elettrica - 01917-0 (1.61 mb)
Energia elettrica - 01918-0 (1.61 mb)