valutazioni - 4, GPA: 4.3
(
)
)
|
Facilità d'uso
Protected by a 25 amp circuit breaker. FULL POWER SWITCH – Switch used to convert every receptacle on the panel, when placed in the 120 position, to a 120 volt receptacle. This will allow you to receive the full capacity of the generator by using all 120 volt receptacles. When in the 120/240 position, you will only be able to use half of the 5800 watts when using the 120 volt receptacles. But in this position, the full 5800 watts can be received in the 240 twistlock receptacle. AIR CLEANER- Includes filter element and foam pre-cleaner that limits the amount of dirt that enters the engine. NOTE: When in the 120 position, each receptacle has the ability to reach the maximum 7500 surge wattage for inductive motors that require 7500 watts or below to start. In the 120/240 position, the 120 volt receptacles will only reach 3750 surge watts. 120 VOLT RECEPTACLES 120/240 TWISTLOCK RECPTACLE 120 VOLT TWISTLOCK RECEPTACLES ENGINE RUN/STOP SWITCH FULL POWER SWITCH ENGINE OIL FILL AIR CLEANER 9 — ENG RECEPTACLES Battery Installation Your generator is equipped with 120-volt duplex receptacles, a 120-volt twistlock receptacle and a 120/240-volt twistlock receptacle. The unit is equipped with a 15-amp circuit breaker for the 120-volt duplex receptacles and two 25-amp circuit breakers for the 120-volt twistlock and for the 120/240-volt twistlock receptacle. These circuit breakers are provided to protect the generator against electrical overload. If the circuit breaker trips, unplug all electrical loads from the generator. Let the circuit breaker cool down. Push circuit breaker button to reset. FULL POWER SWITCH Your Craftsman generator has a full power switch on the control panel. This switch has two positions: 120 VOLT ONLY, and 120/240 VOLT. 120 Position When placed in the 120 position, (shown below) every receptacle on the panel will be converted to a 120 volt receptacle. 240-volt power is not available. This position allows full capacity of the generator to be received by using all 120-volt receptacles. While in the 120 position, each receptacle has the ability to reach the maximum 7500 surge wattage for inductive motors that require 7500 watts or below to start. 120V 120/240V 120/240 Position When in the 120/240 position, (shown below) only half of the 5800 watts can be received when using the 120-volt receptacles and the 120/240-volt twistlock receptacle will be converted to allow the full 5800 watts to be received from this one receptacle. Also in this position, the 120-volt receptacles will only reach a maximum of 3750 surge watts. 120V 120/240V IMPORTANT: Do not move the full power switch while powering electrical equipment. Unplug all items before moving the switch. Failure to do so can damage the switch. To obtain electric start capability, you must install a (12 volt – 45 A.H.) battery. The battery should be properly serviced and fully charged prior to installation. Install the battery as follows: • Place battery in rack with terminals facing towards generator head. • Place battery bracket over battery as shown (opposite battery terminals). • Connect black battery cable from battery post indicated with NEGATIVE (-) to frame with bolt as shown below. • Connect red battery cable from battery post indicated with POSITIVE, (+) to right post on starter solenoid. solenoid(+) Positive Battery Cable Connection GENERATOR CAPACITY Exceeding the rated capacity of your generator can result in serious damage to your generator and connected electrical devices. You should observe the following to prevent overloading the unit: • Starting and running wattage requirements must be calculated to match your generator wattage capacity. 10 — ENG • Resistive load appliances such as light bulbs, TV’s and microwaves, have the same starting and running wattage. The wattage used for calculating the capacity can usually be found on each of these appliances. Some inductive appliances and tools will list on the motor name plate, the starting and running voltage and amperage requirements. Use the following formula to convert voltage and amperage to wattage: (Volts X Amp = Watts) Inductive load appliances and tools such as refrigerators, air compressors and washers require approximately 2 to 4 times the listed running wattage for starting the equipment. This initial load only lasts for a few seconds on start-up but is very important when figuring your total wattage to be used. NOTE: Always start your largest electric motor first, and then plug in other items, one at a time. The guide below is provided to assist you in determining the appliances and tools that can be run with the wattage capacity of your generator. Extension Cord When using an appliance or tool at a considerable distance from the generator, a 3-wire extension cord that has a 3-blade grounding plug and 3-slot receptacle that accepts the tool’s plug should be used. A cord of adequate size must be used. A minimum of 12 gauge wire size with at least a 20 amp draw can be used. When...
Questo manuale è adatto anche per i modelli :Energia elettrica - MGP-679580 (718.72 kb)