valutazioni - 1, GPA: 4
(
)
)
|
Facilità d'uso
f) GAS CONNECTION. Make gas connection between manual shut off valve and furnace valve with approved connectors. Compounds used on threaded joints of gas piping shall be approved for use with L.P. gas. The gas lines must be checked for leaks by the installer with soapy water or liquid detergent, never an open flame. If connections are not exposed, a pressure test must be run. Be sure to disconnect the gas supply line from the appliance valve before pressure testing. The manifold pressure is pre-set at the factory and should be 3.5” w.c. for Natural Gas and 10” w.c. for L.P. gas. The minimum inlet pressure for Natural Gas is 4.5” w.c. and 11” w.c. for L.P. Gas, “for purpose of input adjustment”. The maximum inlet pressure should never exceed 7.0” w.c. on Natural Gas or 14” w.c. on L.P. Gas. STEP 5. INSTALLING REAR TRIM KIT a) Secure right and left trim kit sides to the wall and trim kit brackets with eight #8 screws provided. See figure 11. The back of the heater should now be spaced 5” from the wall. b) Remove the temperature sensing unit from the back of the heater. Save the nylon attachment clip and the #8 screw. c) Slide the temperature sensing unit through the 1/2” bushing located on the right trim kit side. Viewed from the front of the heater. d) Secure the temperature sensing unit to the outside of the right trim kit side using the nylon clip and #8 screw saved from step B. Engagement hole provided. e) Secure trim kit top panel to trim kit sides with four #8 screws provided. f) Plug power supply cord into a 115V grounded electrical outlet. g) Turn the manual gas supply valve to the “on” position. HEATER IS NOW INSTALLED, FOLLOW LIGHTING INSTRUCTIONS. Trim Kit Top Trim Kit Right Side Trim Kit Left Side 1/2” Bushing Trim Kit Bracket (4) FIGURE 11 Page 9 FOR YOUR SAFETY READ BEFORE OPERATING WARNING: If you do not follow these instructions exactly, a fire or explosion may result causing property damage, personal injury or loss of life. A. This appliance does not have a pilot. It is • If you cannot reach your gas supplier, call equipped with an ignition device which the fire department. automatically lights the burner. Do not try to light the burner by hand. C. Use only your hand to push in or turn the gas control knob. Never use tools. If the knob will B. BEFORE OPERATING smell all around the not push in or turn by hand, don’t try to repair appliance area for gas. Be sure to smell next it, call a qualified service technician. Force or to the floor because some gas is heavier than attempted repair may result in a fire or explosion. air and will settle on the floor. WHAT TO DO IF YOU SMELL GAS: D. Do not use this appliance if any part has been • Do not try to light any appliance. under water. Immediately call a qualified service • Do not touch any electric switch; do not technician to inspect the appliance and to use any phone in your building. replace any part of the control system and any • Immediately call your gas supplier from a gas control which has been under water. neighbor’s phone. Follow the gas supplier’s instructions. OPERATING INSTRUCTIONS 1. STOP! Read the safety information above on 5. Remove front panel. this label. 6. Pull the gas control lever DOWN clockwise 2. Set the thermostat to lowest setting. to “OFF”. Do not force. 3. Turn off all electric power to the appliance. 7. Wait five (5) minutes to clear out any gas. Then 4. This appliance does not have a pilot. It is smell for gas, including near the floor. If you equipped with an ignition device which auto-smell gas, STOP! Follow “B” in the safety matically lights the burner. Do not try to information above on this label. If you don’t light the burner by hand. smell gas, go to the next step. 8. Push gas control lever UP counterclockwise to “ON”. 9. Replace front panel. 10. Turn on all electric power to the appliance. 11. Set thermostat to desired setting. 12. If the appliance will not operate, follow the instructions “To Turn Off Gas To Appliance” and call your service technician or gas supplier. TO TURN OFF GAS TO APPLIANCE 1. Set the thermostat to lowest setting. 4. Pull the gas control lever DOWN clockwise 2. Turn off all electric power to the appliance to “OFF”. Do not force. if service is to be performed. 5. Replace front panel. 3. Remove front panel. Gas Inlet Gas control knob shown in “OFF” position A. This appliance does not have a pilot. It is • If you cannot reach your gas supplier, call equipped with an ignition device which the fire department. automatically lights the burner. Do not try to light the burner by hand. C. Use only your hand to push in or turn the gas control knob. Never use tools. If the knob will B. BEFORE OPERATING smell all around the not push in or turn by hand, don’t try to repair appliance area for gas. Be sure to smell next it, call a qualified service technician. Force or to the floor because some gas is heavier than attempted repair may result in a fire or explosion. air and will settle on the floor....
Questo manuale è adatto anche per i modelli :Elettrico - HEDV404 (202.53 kb)