valutazioni - , GPA: ( )

Istruzioni per l'uso United States Stove, Modello 3600PB

Produttore : United States Stove
File Size : 1.38 mb
File Nome : d8d54968-9e3e-4f72-99fd-6ad462198633.pdf

Lingua di insegnamento:

Il documento viene caricato, si prega di attendere

Scarica la tua primo

Il documento viene caricato, si prega di attendere

Scarica la tua primo

To check flue outlet remove top of baffle by lifting and pulling out at end. Use a flashlight to check flue outlet. Clean and repair as necessary. Always replace top baffle before relighting stove. 2. Check that glass is not cracked or chipped and that sealing rope is in good condition. Replace as necessary. 3. When the room is dark, use a strong flashlight to check the sealing of the stove at the edge and corners for leaks. Any leaks or cracks found should be repaired with fire cement or damaged parts should be replaced with genuine spare parts. 4. Check that stove door is tight and well sealed when closed. Place a strip of paper into the stove and close the door, try to pull out paper. You should feel some resistance to your pull, check several points around the door. If it pulls out too easily, replace the rope and seal in place with a suitable high temperature sealant. At times, especially when the air controls are turned to low settings or when damp wood is used, the stove glass will blacken. This is caused by fuel that is not completely burnt, but the build-up on the inside of the glass will normally burn off when a good hot fire is established in the stove. There may be times however when you need to clean the glass. To do this, use a soft cloth and a non-abrasive glass cleaner. Only ever clean the glass when the stove is cold. When loading fuel into the stove, always make sure it is not protruding out through the door opening, as this may break the glass when you close the door. This is especially relevant when loading logs. Always close the door gently. Do not operate with broken or cracked glass. If the glass does crack when the stove is lit, let the fire die out. Do not open the door until the stove has fully cooled. Replace the glass only with the specified replacement part before re-using the stove. Care of Glass 1. Remove the door from the stove and place on a flat surface. 2. Carefully remove all of the glass clips from the inside of the door. 3. Gently remove the glass panel and gasket. 4. Using a wire brush, remove all remaining debris from the glass area. 5. Apply a small bead of gasket/stove cement and the new gasket. Do not overlap the ends of the gasket rope. 6. Center the new glass panel over the gasket and reinstall the glass clips. 7. It may be necessary to retighten the glass clips after the stove has be burned and the gasket has been seated. Important: 1. It is extremely important to tighten the glass clips slowly and in an alternating pattern. 2. Always wear protective gloves when you handle glass with sharp edges. Always use genuine replacement parts. Only ever make replacements when the stove is cold. The stove should only be cleaned using a damp cloth. Some cleaning products may leave stains on the stove surface. Never use abrasive cloths as these may scratch the surface. Painted stoves can be re-painted by using a good quality, high temperature stove paint. When re-painting, make sure there is plenty of ventilation and follow the manufacturer’s instructions. Allow the paint to fully dry before lighting the stove and allow extra ventilation for the first couple of fires as some fumes may emit from the stove as the paint cures. Replacement of Glass Replacing parts Surface Finish Trouble Shooting Fire Not Burning A stove not burning is generally caused by either a shortage of air and/or incorrect or damp fuel. If fuel is not the problem check: • That the air controls are opened. • There is no blockage in the flue system. • That the open end of the flue is above the height of any nearby obstructions. • That there is a sufficient air supply into the room and that this supply is not being taken by an extractor fan. Glass usually blackens when: • The fuel is not being burned efficiently because of starvation of air. • Bad quality or damp fuel is being used. • Balance between primary and secondary air is incorrect. Try to introduce more air into the stove, especially through the secondary air control on the top of the stove door as this air flows down over the glass to help burn off the creosote. For optimum efficiency always use a good quality wood. Glass Blackens If the stove is properly installed it should not emit any smoke into your room. Should this happen, Check that your room is not air tight. This can easily be checked by opening a door or window. If the smoking stops you need to provide an additional air supply into the room. If this is not the problem, check if your chimney is blocked or obstructed and that you are not getting a down draft caused by the location of the open end of the flue pipe or chimney. If the problem persists contact your dealer and ask him to get your chimney and stove installation checked. This is usually caused by too much draft or air. • Firstly try reducing the air supply to the stove by closing down your air controls, if this fails then you may have damage to the sealing. • Check the condition of the door sealing rope and the joints within the sto...