valutazioni - 2, GPA: 4.5
(
)
)
|
Facilità d'uso
Box 151 • South Pittsburg, TN 37380 • Safety Tested to ASTM-E 1509, (UM) 84-HUD American Harvest Safety Notice: If this heater is not properly installed, a house fire may result. For your safety, follow the installation directions. Contact local building or fire officials about restrictions and installation requirements peculiar to your area. Do Not Plug this appliance into an electrical outlet before reading and understanding all operations and always unplug the unit before attempting any work or maintenance. Do not connect this heater to any chimney flue already serving another appliance. Carefully observe and maintain all clearances to combustibles. A note about fuel: Use only dried shelled corn with a moisture content of 14% or less (11 to 12% provides the best results); any pellet fuel used should have an ash content of 1% or less. If not, efficiency will suffer. This heater has successfully burned pellets with a 2-1/2% ash content, though less ash is preferred and more efficient. Your American Harvest Multi-Fuel Heater operates on a negative pressure. Therefore, all venting connections (elbows, T-pipe) must be sealed and airtight. i Use Hi-Temp silicone at each joint or connection. READ THIS ENTIRE MANUAL, THOROUGHLY, BEFORE ATTEMPTING TO INSTALL AND/ OR BURN YOUR NEW AMERICAN HARVEST *MULTI-FUEL HEATER. FAILURE TO FOLLOW THESE INSTRUCTIONS MAY RESULT IN PROPERTY DAMAGE, BODILY INJURIES OR EVEN DEATH. *This heater is capable of burning wood, biomass pellets and a wide variety of grains, including corn, soybeans, cherry and olive pits, and all larger seeds. SAVE THESE INSTRUCTIONS UNITED STATES STOVE COMPANY GRANTS NO WARRANTY, IMPLIED OR STATED, FOR THE INSTALLATION OR MAINTENANCE OF THE HEATER AND ASSUMES NO RESPONSIBILITY FOR ANY CONSEQUENTIAL DAMAGE(S). Tested & Listed By Portland Oregon USA Omni-Test Laboratories, Inc. US You’ve purchased one of America’s Finest Multi-fuel Burning Heaters. By heating with fuels such as corn and pellets, you’re helping CONSERVE AMERICA’S ENERGY! NOTE: YOUR UNIT MUST BE INSTALLED BY A QUALIFIED INSTALLER, such as an NFI (National Fireplace Institute) Certified Specialist We strongly suggest installing smoke detectors in your home if not already installed. Initial burn off may cause slight smoke and odor the first few hours of operation. Perform initial burn outside if possible SPECIFICATIONS United States Stove Company reserves the right to alter products, specifications and price without notice. Safety Tested & Listed to ASTM- E 1509, (UM) 84-HUD, by OMNI Test Laboratories, Inc., Portland, Oregon USA Heat Input (as tested) 45,000 BTU/HR Heat Output (as tested) . 35,100 BTU/HR Heating Capacity 1,000-2,000 Sq. Ft . Fuel Storage Capacity 60 Lbs. Width 29 in./737mm Height 6041TP/6041HF 31 in./787mm 6041I 24 in./610mm Depth 28 in./711mm . BTU output will vary, depending on the brand, type and quality of fuel and the moisture content. Consult your dealer for best results. . Based on post 1982 home construction, requiring 35 BTU/Hr per Sq. Ft. Remember, this heater should not be used as the only source of heat in the house. Power outages and neglect of periodic maintenance will result in a total loss of heat. USSC USSC 3 1 1 2 2 A A B B Assembly 1. Unpack unit and make sure all components are included; (4) Legs, and all hardware for installation. 2. Fold the corner padding from the carton and lay it on the floor behind the unit. This is used to hold the heater up off the floor to install the legs. Gently tilt the heater on its back, door opening up. 3. Assemble the legs as shown using the eight(8) 1/4-20 bolts supplied. 4. After all bolts and screws have been tightened properly, carefully set the heater back up on the legs. 6041HF ASSEMBLY 6041TP PEDESTAL TRIM ASSEMBLY Assemble trim pieces as shown with the screws provided in the parts bag. After trim assembly, attach to the pedestal base at the location shown using the screws provided. 4 USSC (a) (a) (c) (h) (f) (g) (b) (e) 6041I ASSEMBLY (i) (j) For the following assemblies, we suggest locating the unit near it’s desired location. Depending on installation, you may want to connect the exhaust venting before installing the facade parts. Assembly - Facade (Surround) Remove contents from packaging and make sure you have all components: (2) Top Facade (a) (1) Left Side Facade (b) (1) Right Side Facade (c) (4 pieces)Facade Trim Kit (d) (1) Feed Door Spring Handle (e) (1) Damper Spring Handle (f) (1) Ash Pan “U” shaped Handle (g) (1) Access Door Knob (h) (1) PCB Cover (i) (1) Panel Cover (j) (1) Auger (in ash pan) (1) Power Cord (1) Burnpot Poker (k) Mounting Hardware Start by mounting either the left or right side facade pieces to the unit using four(4) of the supplied #10 x 1/2 screws. Then put the two(2) top facade pieces together with two(2) of the #10 x 1/2 screws provided. Attach the top facade assembly to the unit with eight(8) of the same screws. Control Board (PCB) Re-location Remove the left side fro...
Questo manuale è adatto anche per i modelli :Elettrico - 6041HF (3.03 mb)
Elettrico - 6041I (3.03 mb)
Elettrico - 6041TP (3.03 mb)