valutazioni - 3, GPA: 3.3
(
)
)
|
Facilità d'uso
Protect yourself and others by observing all safety information. Failure to comply with instructions could result in personal injury and/or property damage! Retain instructions for future reference. ® Dayton Propane Construction Heater Description Dayton model 3VG81 is a 150,000 Btu/Hr propane construction heater with built-in thermostat. This heater uses propane gas for combustion. It is primarily intended for temporary heating of buildings under construction, alteration, or repair. This heater should only be used indoors but never in occupied dwellings. Products of combustion are vented into the area being heated. Unpacking 1. Remove all packing items applied to heater for shipment. Keep plastic cover caps (attached to inlet connector and hose/regulator assembly) for storage. 2. Check all items for shipping damage. If heater is damaged, promptly inform dealer where you bought heater. Figure 1 – Model 3VG81 GENERAL HAZARD WARNING Failure to comply with the precautions and instructions provided with this heater can result in death, serious bodily injury, and property loss or damage from hazards of fire, explosion, burn, asphyxiation, carbon monoxide poisoning, and/or electrical shock. Only persons who can understand and follow instructions should use or service this heater. If you need assistance or heater information such as an instructions manual, labels, etc. contact the manufacturer. Fire, burn, inhalation, and explosion hazard. Keep solid combustibles such as building materials, paper or cardboard, a safe distance away from the heater as recommended by the instructions. Never use the heater in spaces which do or may contain volatile or airborne combustibles, or products such as gasoline, solvents, paint thinner, dust particles, or unknown chemicals. Not for home or recreational vehicle use. The heater is designed for use as a construction heater under ANSI Z83.7/CSA 2.14. The primary purpose of construction heaters is to provide temporary heating of buildings under construction, alteration or repair, and to provide temporary emergency heat. Properly used, the heater provides safe economical heating. Products of combustion are vented into the area being heated. We cannot foresee every use which may be made of our heaters. Check with your local fire safety authority if you have questions about heater use. Other standards govern the use of fuel gases and heat producing products for specific uses. Your local authorities can advise you about these. Printed in U.S.A. Form 5S3928 03430 1002/213/VCPVP ® Version B - For Reduction G016.J Dayton Operating Instructions and Parts Manual 3VG81 ® Dayton Propane Construction Heater 3VG81 Specifications General Safety Information Output Rating 150,000 Btu/Hr IMPORTANT: Make certain you read and understand all warnings. Keep these Fuel Propane Vapor Only instructions for reference. They are your Fuel Consumption 7.0 Pounds/Hour (1.6 Gallons/Hour) guide to safe and proper operation of this Regulator Input Pressure Minimum: 10 Psig heater. Maximum: Tank Pressure Safety information appears throughout Regulator Output Pressure 12.5" WC (Factory Preset) these instructions. Pay close attention to Manifold Pressure 9.8" WC (Factory Preset) them. Below are definitions for the safety Ignition Electronic direct spark, D.S.I. information listed throughout this manual. Ignitor Gap Minimum: 0.13" Under this heading, Maximum: 0.15" installation, operating Temperature Control Built-In Thermostat and maintenance procedures or practices Air Flow 550 Cfm will be found that, if not carefully followed, Volts 120 Vac 60 Hz I Phase WILL result in IMMEDIATE serious personal Amps 2.2 injury or death. Motor HP 1/8 Under this heading, Motor RPM 3,450 installation, operat- Dimensions 361/4"L x 20"H x 141/2"W ing, and maintenance procedures or Heater Weight 27 Lb practices will be found that, if not Shipping Weight 35 Lb carefully followed, COULD result in severe personal injury or death. Product Identification Under this heading, installation, operating, and maintenance procedures or Hot Air Outlet HandleUpper ShellOn/Off Switch AssemblyInlet ConnectorLower ShellThermostatKnobFan Guard practices will be found that, if not carefully followed, MAY result in minor personal injury, product or property damage. (Front) IMPORTANT: Not every possible circumstance that might involve a hazard can be anticipated. The warnings in this manual and on tags or decals affixed to the unit are Power Cord therefore not all-inclusive. If a procedure, work method, or operating technique not specifically recommended by Dayton is used, you must make sure it is safe for you and others. You should also ensure that equipment will not be damaged or made unsafe by the Hose/Regulator operating or maintenance method you choose. Figure 2 - Product Identification 2 Dayton Operating Instructions and Parts Manual Model 3VG81 General Safety Information (Continued) This product contains and/or generates chemicals know to the State o...