valutazioni - 2, GPA: 3.5 ( )

Produttore : Vermont Casting File Size : 5.21 mb File Nome : Lingua di insegnamento:

Place the key on your work surface with the threaded holes facing up. 2. Place the column right assembly onto the key. (Fig. 4) 3. Place the column left assembly onto key. (Fig. 5) KT424 column right assy 9/03 Key Column Right Assembly KT424 Fig. 4 Place column right assembly onto key. KT425 column left assy 9/03 Key Column Left Assembly KT425 Fig. 5 Place column left assembly onto key. 4. Install the upper mounting bracket. Use the upper mounting without the marked “R” stamped on the face. (Fig. 6) 5. Fasten the upper mounting bracket to the key with a 1/4-20 wing screw and 1/4 flat washer finger tight. (Fig. 6) 30004451 5 KT436 upper mounting bracket 9/03 1/4-20 Wing Screw 1/4 Flat Washer Upper Mounting Bracket without Marked “R” Stamping Boot Boot KT426 Fig. 6 Install upper mounting bracket. 6. Fasten the upper mounting bracket to both column assemblies using two (2) 1/4-20 wing screws and two (2) 1/4 flat washers per side, finger tight. The distance between the insides of the columns should measure 29...” (743 mm). 7. Adjust the column/boot length (measure from the bottom side of the key to the bottom of the boot). It should measure 22...” (565 mm). 8. Position the surround in front of the insert and, with the help of an assistant, gently lift the surround up and over the top sheet metal flange. At the same time, align the bottom brackets through the slots on the side flange. As you lower the surround onto the insert, the side clips and top bracket will engage. If height and width adjustments are required, lift the surround up and out. Make the adjustments. Regardless if adjustments were made or not, tighten all wing screws fasteners and return the surround to the insert. (Fig. 7) Assembly complete. ............ .............................................. ........ Top Flange Side Flange KT1014 Fig. 7 Lift surround up and over top flange and up and through side flange holes. 6 30004451 Bevel Cast Trim Surround Model: LHEABSL Steel Surround Panels Models: LHE30SSB, LHE30SLB, LHE30SLGA Read these instructions before beginning installation. Check Contents of Shipping Carton Examine contents of shipping carton. If any parts are missing or damaged, contact your local dealer before starting installation. Surround Parts Trim kit assembly Trim mounting hood Trim bottom (2) (not used on Montpelier Insert) Trim deflector (not used on Montpelier Insert) Hardware package Installation Instructions Install the Bevel Cast Trim Surround or Steel Surround Panels after all other installation work has been completed, thoroughly checked, and tested for proper operation, leaks and installation requirements. 1. Remove all plastic from trim kit. 2. Before installing trim kit, LHEABSL, some modifications must be completed. Remove two (2) or four (4) wing nuts from the back of the trim kit and locate the trim mounting hood to the two (2) or four (4) outer holes. Fasten the wing nuts back in position. (Fig. 8) KT386 Trim mounting hood 5/1/03 djt Wing Nut Trim Mounting Hood Use the Inner Mounting Holes KT386 Fig. 8 Adjust trim mounting hood to correct hole location. Assembly Instructions 1. Once the insert has been installed and tested for proper operation as directed, stand the Bevel Cast Trim Surround or Steel Surround Panels in front of the insert. 2. Position the surround in front of the insert and with the help of an assistant, gently lift the surround up and over the top sheet metal flange, at the same time, align the bottom brackets through the slots on the side flanges. (Fig. 9) 3. Adjust the surround, left to right, so there is an equal reveal on either side. Secure by applying downward pressure until the brackets have engaged onto the insert. (Fig. 9) Assembly complete. KT1015 install trim 3/08 djt Top Flange Side Flange KT1015 Fig. 9 Lift surround up and over top flange and up and through side flange holes. 30004451 7 Georgian Cast Surround Models: 30DVSGTKCB, 30DVSGTKB DVSGTKCB - Classic black cast iron DVSGTKB - Ebony black enameled cast iron NOTE: Cast iron parts can be heavy, an assistant would be advisable for this installation. CAUTION: Porcelain enamel is fragile. The finish can be easily damaged if castings are not handled carefully. Always place castings on a protective surface, such as a towel, blanket or carpet. Tools required: 7/16” wrench, measuring tape, Phillips screwdriver, straight edge, (i.e. yard stick, broom handle, pc of wood) Check Contents of Shipping Carton Compare contents of carton in Figure 10 with actual parts received. If any parts are missing or damaged, contact your local dealer before starting installation. Surround Parts 1. Left Mantel 2. Left Trim 3. Center Trim 4. Right Mantel 5. Right Trim 6. Right Column 7. Left Column 8. Center Mantel Hardware 9. Hex Head Bolt 1/4-20 x 5/8”, (3) 10. Hex Head Bolt 1/4-20 x 3/8”, (10) 11. Flat Washer (13) 1 8 2 3 7 6 4 5 9 10 11 CAR189 Georgian 30 trim 8/06 Figure 10 CAR189 3/8” Hex Head Bolt Flat Washer Center Mantel Left Mantel Right Mantel KT662...

Scarica la tua

Per scaricare, digitare 2 cifre :