valutazioni - , GPA: ( )

Istruzioni per l'uso Lennox Hearth, Modello EBVI30

Produttore : Lennox Hearth
File Size : 2 mb
File Nome :

Lingua di insegnamento:

Il documento viene caricato, si prega di attendere

Scarica la tua primo

Il documento viene caricato, si prega di attendere

Scarica la tua primo

Any fireplace component, which is removed, must be retained so they can be reinstalled to restore the fireplace to its original operating condition. The removal of any part must not alter the integrity of the outer shell of the pre-engineered fireplace cabinet in any way. If any components are removed from (or altered) Room Air Circulation Blower IMPORTANT: BLOWER GROUND WIRE WITH POWER CORD GREEN WIRE SHOULD BE ATTACHED TO THE GROUND SCREW. FAILURE TO DO SO WILL RESULT IN A POTENTIAL SAFETY HAZARD. THE APPLIANCE MUST BE ELECTRICALLY GROUNDED IN ACCORDANCE WITH LOCAL CODES OR, IN THE ABSENCE OF LOCAL CODES, THE NATIONAL ELECTRICAL CODE, ANSI/ NFPA 70 - LATEST EDITION. (IN CANADA, THE CURRENT CSA C22-1 CANADIAN ELECTRICAL CODE - LATEST EDITION. WARNING: THE POWER CORD MUST BE PLUGGED DIRECTLY INTO A PROPERLY GROUNDED THREE-PRONG 120 VOLT, 60 HZ WALL RECEPTACLE. DO NOT CUT OR REMOVE THE GROUNDING PRONG FROM THIS PLUG. DO NOT ROUTE Figure 25 from the existing fireplace, a Warning Label (see below) must be affixed inside the fireplace firebox, so that it shall be visible upon removal of the fireplace insert. Note: RTV high temperature silicone is an approved adhesive. 1/8" Min. (3 mm) Thermocouple Igniter Rod Hood 3/8" Min. (9 mm) Thermopile Pilot Nozzels you should experience any problem, first refer to the troubleshooting guide in this manual. If problem persists, contact your Lennox Hearth Products Dealer. Figure 26 WIRING DIAGRAMS POWER CORD UNDER OR IN FRONT OF APPLIANCE. Blower Wiring Diagram Fireplace Warning Label 120 V AC (Provided in Accessory Package) WARNING THIS FIREPLACE HAS BEEN ALTERED TO ACCOMMODATE A FIREPLACE INSERT AND SHOULD BE INSPECTED BY A QUALI- FIED PERSON PRIOR TO RE-USE AS A CONVENTIONAL FIREPLACE. (Ground) GreenHot (Live) Power Cord (Neutral) White To light the burner, rotate the gas valve control knob counterclockwise to the “ON” position then turn “ON” the off/on switch mounted on the surround assembly (see Figures 1 & 2 on Page 3) or operate the burner with the optional remote control, wall thermostat or control switch. With proper care and maintenance, your appli- Black Fan Disc ance will provide many years of enjoyment. If BLOWER OPERATION When the insert heats up, the blower will automatically be turned on by the fan disc located under the firebox bottom on the front left side. It will come on at the speed determined by the rheostat located on the side surround panel (see Figure 4 on Page 4). To adjust the blower speed, dial the rheostat to the desired speed setting. Rotate the dial down (clockwise), just past the Wiring diagrams are provided here for reference purposes only. This information is also provided on schematics attached directly to the appliance on a pullout panel located within the control compartment. CAUTION Black BlackRed Rheostat Label all wires prior to discon click (the first ON position) for the highest speed Black nection when servicing con- setting. Turning the knob further clockwise will provide slower blower speeds. Note: If the rheostat is not turned “on,” the trols. Wiring errors can cause Blower improper and dangerous appli- Assembly Figure 27 blower will not operate. ance operation. NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE. Figure 28 If original wire as supplied must be replaced, it must be replaced with Type AWM 105°C, 18 gauge wire. * Off/on Switch, Optional Thermostat or Remote Control Receiver Thermopile * Switch Spill Switch SIT & Honeywell Millivolt Wiring Diagram THTP THTP Figure 28 If original wire as supplied must be replaced, it must be replaced with Type AWM 105°C, 18 gauge wire. * Off/on Switch, Optional Thermostat or Remote Control Receiver Thermopile * Switch Spill Switch SIT & Honeywell Millivolt Wiring Diagram THTP THTP If you encounter any problems or have any questions concerning the installation or application of this system, please contact your distributor. For the number of your nearest Lennox dealer, please call 800-9-Lennox. LENNOX HEARTH PRODUCTS 1110 West Taft Avenue Orange, CA 92865 Visit us at WARRANTY INFORMATION Your gas appliance is covered by a limited twenty-year warranty. You will find a copy of the warranty accompanying this manual. Please read the warranty to be familiar with its coverage. Retain this manual. File it with your other documents for future reference. REPLACEMENT PARTS A complete parts list is found at the end of this manual. Use only parts supplied from the manufacturer. All parts should be ordered through your Lennox Hearth Products Distributor or Dealer. Parts will be shipped at prevailing prices at time of order. When ordering repair parts, always give the following information: 1. The model and serial number of the appliance (see rating plate in control compartment of appliance). 2. The part number & description of part (see Page 17). 3. The quantity required. 4. The installation date of the appliance. NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE. ACCESSORY C...