valutazioni - 4, GPA: 4.3
(
)
)
|
Facilità d'uso
This appliance must be installed only in locations where the potential for physical damage to the appliance (i.e., due to physical contact) is reduced to a minimum. The installer must inform the owner/operator of this appliance that precautions must be taken to protect the appliance from physical damage. This appliance produces radiant heat. Therefore, it must be located at least six feet away from any LP-Gascontainerand ust not be directed toward any LP-Gas container within 20 feet. Due to high surface and exhaust temperatures, adults and children must observe clearances to avoid burns or clothing ignition. The heater must be installed in a location such that it will not be exposed directly to water spray, rain, and/or dripping water. Use of this heater in a draft/windy area decreases its efficiency. If possible, operate the unit in a draft free area. PIPING For Model 125-R (for use with LP-Gas) This model may be connected to a self-contained LP-Gas supply system using the hose and regulator assembly supplied with the appliance, OR, it may be connected to a permanently installed LP-Gas supply system. If connected to a self-contained LP-Gas supply system, the hose assembly must be inspected prior to each use of the heater. If it is evident that there is excessive abrasion or wear, or if the hose is cut, it must be replaced prior to the heater being put into operation. If connected to a self-contained LP-Gas supply system, the cylinder must have no less than a minimum capacity of 20 pounds and no more than a maximum capacity of 100 pounds of LP-Gas. DO NOT connect this appliance to a cylinder having less than a nominal 20 pounds capacity of LP-Gas. DO NOT connect this appliance to more than one (1) 100 pound cylinder. WARNING NEVER USE A FORK LIFTTRUCK TYPE CYLINDER. The connection of Model 125-R to an LP-Gas cylinder must be made in a well ventilated area using the regulator and hose assembly supplied with the appliance. DO NOT attempt to adjust this regulator. It has been preset at the factory to provide safe and proper operation of the appliance. Use a 7/8” open end wrench to connect the POL fitting (supplied with the LP regulator) to the LP-Gas cylinder. Turn the POL nut in a counter-clockwise direction (left hand thread) until tight. DO NOT use pipe compound on POL threads. The heater must be located at least six feet away from any LP-Gas cylinder and must not be directed toward any LP-Gas cylinder within 20 feet. If more than one heater is used, they and the supply cylinders must be separated by at least 20 feet. The gas supply must be turned off at the LP-Gas supply cylinder when the heater is not in use. When the heater is to be stored indoors, the connection between the LP-Gas supply cylinder and the heater must be disconnected and the cylinder removed from the heater and stored in accordance with Chapter 5 of the Standard for the Storage and Handling of Liquefied Petroleum Gases. ANSI/ NFPA 58 (U.S.) OR CAN/CGA B149.2 (Canada). If connected to a permanently installed LP-Gas supply system, the system requires the use of a two-stage gas regulator assembly which is normally provided by your LP Gas dealer as part of the LP-Gas supply system. Consult with your local LP Gas dealer for details concerning proper equipment and installation. 3 Operating Instructions and Owner’s Manual ODOR FADE WARNING WARNING heater dataplate, or contact the Scheu Products Company to determine combustion air ventilation requirements of the Asphyxiation Hazard heater. • Do not use this heater for heating human living quarters. • Lack of proper ventilation air will lead to improper • Do not use in unventilated areas. combustion. • The flow of combustion and ventilation air must not be • Improper combustion can lead to carbon monoxide obstructed. poisoning leading to serious injury or death. Symptom of • Proper ventilation air must be provided to support the carbon monoxide poisoning can include headaches combustion air requirements of the heater being used. dizziness and difficulty in breathing. • Refer to the specification section of the heater’s manual, FUEL GAS ODOR LP gas and natural gas have man-made odorants added specifically for detection of fuel gas leaks. If a gas leak occurs you should be able to smell the fuel gas. Since Propane (LP) is heavier than air you should smell for the gas odor low to the floor. ANY GAS ODOR IS YOUR SIGNAL TO GO INTO IMMEDIATE ACTION! • Do not take any action that could ignite the fuel gas. Do not operate any electrical switches. Do not pull any power supply or extension cords. Do not light matches or any other source of flame. Do not use your telephone. • Get everyone out of the building and away from the area immediately. • Close all propane (LP) gas tank or cylinder fuel supply valves, or the main fuel supply valve located at the meter if you use natural gas. • Propane (LP) gas is heavier than air and may settle in low ODOR FADING - NO ODOR DETECTED • Some people cannot smell well. Som...
Questo manuale è adatto anche per i modelli :Elettrico - 125-RN (179.14 kb)