valutazioni - , GPA: ( )

Istruzioni per l'uso Gas-Fired Products, Modello HS125LP

Produttore : Gas-Fired Products
File Size : 974.39 kb
File Nome : 9ba61b99-4c3a-4c2e-a6de-4de3c3ee5234.pdf

Lingua di insegnamento:

Il documento viene caricato, si prega di attendere

Scarica la tua primo

Il documento viene caricato, si prega di attendere

Scarica la tua primo

Provide additional ventilation for any additional fuel- burning appliances and/or additional occupants. CLEARANCE (Minimum clearances to combustible materials) Do not exceed the gas supply pressures shown on rating plates. The maximum inlet gas supply pressures and minimum inlet supply pressures (for purposes of input adjustment) for LP-Gas and Natural gas are shown as follows: MODEL NO. BTU/HR RATING TYPE GAS NORMAL OPERATING POSTION CLEARANCES TO COMBUSTIBLES NATURAL LP-GAS TOP SIDES BACK MH125LP/ HS125LP 125,000* VERTICAL 48” 60” 60” HS125NG 125,000 VERTICAL 48” 60” 60” *Tank size and tank temperature can directly affect BTU output CONTENTS Installation Instructions.................................................... 3 Location .......................................................................... 3 Piping .............................................................................. 3 Operating Instructions ..................................................... 4 Lighting and Shut Down .................................................. 4 Maintenance Instructions ................................................ 5 Replacement Parts List ..................................................... 6 Service and Parts Ordering Information ........................... 8 FOR YOUR SAFETY Do not use this heater in a space where gasoline or other liquids having flammable vapors are stored or used. The heater is designed and approved for use as a construction heater under ANSI Z83.7 / CGA 2.14 - 2000 We cannot anticipate every use which may be made of our heaters. CHECK WITH YOUR LOCAL FIRE SAFETY AUTHORITY IF YOU HAVE QUESTIONS ABOUT APPLICATIONS. Other standards govern the use of fuel gases and heat producing products in specific applications. Your local authority can advise you about these. This appliance is intended to be used primarily for the heating of buildings under construction, alteration or repair. THE STATE OF CALIFORNIA REQUIRES THE FOLLOWING WARNING: WARNING Combustion by-products produced when using this product contain carbon monoxide, a chemical known to the State of California to cause cancer and birth defects (or other reproductive harm). Enerco Group, Inc. | Gas-Fired Infra-Red Portable Construction Heater 2 Operating Instructions and Owner’s Manual INSTALLATION INSTRUCTIONS GENERAL: READ THESE INSTRUCTIONS CAREFULLY. Read and adhere to these instructions. DO NOT allow anyone who has not read these instructions to assemble, light, adjust or operate this heater. DO NOT attempt to operate the heater with any gas other than that indicated on the heater nameplate. For the U.S. and/or Canada, the installation of this appliance must comply with local and/or Provincial codes or, in the absence of these codes, • With the (U.S.) National Fuel Gas Code, ANSI Z223.1 – Latest Edition (for Natural and LP-Gas operation, Models HS125NG, MH125LP, and HS125LP), and with the (U.S) Standard for the Storage and Handling of Liquefied Petroleum Gases, ANSI/NFPA 58 (for LP Gas operation, Model MH125LP, HS125LP), or • with the current (Canadian) CAN/CGA B149.1 AND B149.2 INSTALLATION CODES. This heater (including hose and regulator assembly if applicable) must be inspected before each use and at least annually by a qualified service person. If the hose for Model MH125LP/HS125LP shows evidence of excessive abrasion or wear, or if the hose is cut, it must be replaced prior to the heater being put into operation. The replacement hose assembly shall be that specified by the manufacturer. See the parts list. LOCATION The heater (and LP-Gas supply cylinder if applicable) must be located on a hard, flat, level surface to minimize the risk of accidental tipping. If an LP Gas supply cylinder is used (i.e. with Model MH125LP/HS125LP), the cylinder should be adequately restrained to prevent accidental tipping. DO NOT operate this heater with the supply cylinder in any other than the upright position. This appliance must be installed only in locations where the potential for physical damage to the appliance (i.e., due to physical contact) is reduced to a minimum. The installer must inform the owner/operator of this appliance that precautions must be taken to protect the appliance from physical damage. This appliance produces radiant heat. Therefore, it must be located at least six feet away from any LP-Gas container and must not be directed toward any LP-Gas container within 20 feet. The heater must be installed in a location such that it will not be exposed directly to water spray, rain, and/or dripping water. Use of this heater in a draft/windy area decreases its efficiency. If possible, operate the unit in a draft free area. PIPING For Model MH125LP/HS125LP (for use with LP-Gas) This model may be connected to a self-contained LP-Gas supply system using the hose and regulator assembly supplied with the appliance, OR, it may be connected to a permanently installed LP-Gas supply system. If connected to a self-contained LP-Gas supply...