valutazioni - 5, GPA: 3.6
(
)
)
|
Facilità d'uso
The heater should NOT produce thick black smoke. Note: The burner may be noisy when initially turned on. To eliminate excessive noise from the burner, turn the Control Knob to the LOW position. Then, turn the knob to the level of heat desired. When heater is ON: Emitter screen will become bright red due to intense heat. The color is more visible at night. Burner will display tongues of blue flame. These flames should not be yellow or produce thick black smoke, indicating an obstruction of airflow through the burners. If yellow flame is detected, turn off heater and gas supply and consult “Troubleshooting”. Re-lighting Note: For your safety, Control Knob cannot be turned ‘Pilot” without first depressing Control Knob in "Off" position and then rotating to “Pilot”. 1. Turn Gas Control Knob to “Off”. 2. Wait 5 minutes to let gas dissipate before attempting to relight burner. 3. Repeat the “Lighting” Steps 2 and 3. To turn heater OFF: 1. Rotate Gas Control Knob to “Off" position. Normally, burner will make a slight popping sound when extinguished. 2. Remove Door Plate. 3. Unscrew gas line from regulator. 4.Close Door Plate. Note: After use, some discoloration of the emitter screen is normal. 10 AFTER OPERATING Make sure: • Gas control is in OFF position. • Disconnect Gas line. • Heater is upright in a secure location. MAINTENANCE • To enjoy years of outstanding performance from your heater, make sure you perform the following maintenance activities on a regular basis: Inspect the visible portion of the hose before each use of the appliance; Inspect the entire hose assembly at least annually. • Airflow must be unobstructed. Keep controls, burner, and circulating air passageways clean. Signs of possible blockage include: Gas odor with extreme yellow tipping of flame; heater does NOT reach the desired temperature; heater glow is excessively uneven. • Heater makes popping noises. Spiders and insects can nest in burner or orifices. This dangerous condition can damage heater and render it unsafe for use. Clean burner holes by using a heavy-duty pipe cleaner. • Compressed air may help clear away smaller particles. • Carbon deposits may create a fire hazard. Clean dome and emitter with warm soapy water if any carbon deposits develop. Note : In a salt-air environment(such as near an ocean), corrosion occurs more quickly than normal. • Frequently check for corroded areas and repair them promptly. • Keep exterior surfaces clean. STORAGE Between uses: • Turn Control Knob OFF. • Disconnect LP source. • Store heater upright in an area sheltered from direct contact with inclement weather(such as rain, sleet, hail, snow, debris). If desired, cover heater to protect exterior surfaces and to help prevent build up in air passages. Note: Wait until heater is completely cool before covering. During periods of extended inactivity or when transporting: • Turn Control Knob OFF. • Disconnect LP source and move to a secure, well-ventilated location outdoors. • Store heater upright in an area sheltered from direct contact with inclement weather (such as rain, sleet, hail, snow, dust and debris). If desired, cover heater to protect exterior surfaces and to help prevent build up in passages. 11 PROBLEM TROUBLESHOOTING PROBABLE CAUSE SOLUTION Pilot will not light Pilot will not stay on Burner will not light Tank fuel empty Opening blocked Air in supply system Loose connections Debris around pilot Loose connections Thermocouple bad Gas leak in line Lack of fuel pressure Pressure is low Opening blocked Control not ON Thermocouple bad Pilot light assembly bent Not in correct location Replace LPG tank Clean or replace opening Purge air from lines Check all fittings Clean dirty area Tighten connections Replace thermocouple Check connections Tank near empty. Replace LPG tank. Tank near empty. Replace LPG tank. Remove and clean Turn valve to ON Replace thermocouple Place pilot properly Position properly and retry 12 Distributed By: Well Traveled Living 716 S 8th Street Amelia Island, FL 32034 Toll Free: 866-WTL-SUPP Web: Email: cservice@welltraveled.net 1 YEAR LIMITED WARRANTY-Customers in the Continental US All components are warranted for a period of 1 year after date of purchase by the original owner against defects in materials and workmanship under normal use. This warranty does NOT cover normal wear and weathering, assembly and/or maintenance OR use in a commercial application. At Well Traveled Living's sole discretion, products under warranty will be repaired and/or replaced at no charge to the customer. Any returns sent back to Well Traveled Living must be sent via prepaid freight and in the original retail packaging. For warranty service contact Well Traveled Living at the address, phone numbers or internet site and email listed in this owner's manual. Be sure to have your sales receipt, date of purchase and catalogue/model numbers available when calli...
Questo manuale è adatto anche per i modelli :Elettrico - FireSense 60262 (1.46 mb)
Elettrico - FireSense 60269 (1.46 mb)