valutazioni - 5, GPA: 4 ( )

Produttore : Well Traveled Living File Size : 1.45 mb File Nome : Lingua di insegnamento:

Disconnected cylinders must have threaded valve plugs tightly installed, and must not be stored in a building, garage, or any other enclosed area. . - 4 ASSEMBLY PARTS LIST 1. Burner assembly 2. 4 pcs mesh guard 3. Handle with 2 pcs M6 nuts and 2 pcs flat gaskets 4. Back panel 5. 5 pcs M4x10mm bolts, 5 pcs M4 flat gaskets, and 5 pcs M4 nuts to connect the burner assembly with back panel 6. Regulator with gas hose 7. Door panel 8. 10 pcs M5x12mm bolts and 10pcs M5 nuts for connection of 5 brackets with back panel,5pcs M8x16mm bolts to connect the back panel with base 9. Wheels with 2 pcs M8x16mm bolts and 2 pcs M8 nuts 10. 6 pcs M6x12mm bolts and 6 pcs M6 nuts for connection of 3 cylinder brackets with base and 3pcs M8x25mm bolts for securing the LPG cylinder 11. Base -5- ASSEMBLY ASSEMBLY WARNING: This appliance requires installation by a competent person. Proper assembly is the responsibility of the installer. Step 1 Use 6 pcs M6x12mm bolts and 6 pcs M6 nuts to connect 3 cylinder brackets on the base. The brackets will allow LPG cylinder to rest securely on base. Step 2 Attach the handle to the back panel with 2 pcs M6 nuts and 2 pcs flat gasket. - 6 ASSEMBLY Step 3 Use 10 pcs M5x12mm bolts and 10pcs M5 nuts to connect 5 brackets with back panel, Attach the back panel on the base with 5 pcs M8x16mm bolts. Step 4 Attach the burner assembly to back panel with 5 pcs M4x10mm bolts, 5 pcs M4 flat gaskets, and 5 pcs M4 nuts. -7- ASSEMBLY ASSEMBLY Step 5 Attach the door panel to the back panel. Step 6 Attach the regulator to the burner assembly (see picture to the right) and tighten. Attach the regulator to the LPG cylinder (see below). Warning: Always make sure to check the connection for leaks before using the heater (see page 10). - 8 ASSEMBLY ASSEMBLY Step 7 Attach mesh guards (4 pcs) to burner assembly as shown (see picture to right). - 9 ASSEMBLY AND OPERATION ASSEMBLY AND OPERATION To check for leaks: Your patio heater has been checked at all factory connections for leaks, but you should always check when you attach the LPG cylinder. To check for leaks, follow these instructions: --Assemble all gas connections. --Connect regulator assembly to the propane tank. --Make sure the heater valve is turned OFF. 1) Make soapy solution by mixing 1 part liquid dish soap and 3 parts water. 2) Open the propane tank valve. 3) Spoon several drops (or use squirt bottle) of the soapy solution onto the gas hose /regulator and regulator/cylinder connection. 4) Inspect the connections and look for bubbles. 5) If no bubbles appear the connection is safe. 6) If bubbles appear, there is leakage. Close the propane tank valve, and loosen and re-tighten this connection. 7) Check for leakage again. 8) If bubbles still appear, close the propane tank valve and contact your gas supplier. If a leak is detected, DO NOT attempt to use the heater. MAKE SURE TO CHECK ALL THREE CONNECTIONS BETWEEN THE LPG CYLINDER AND GAS LINE. - 10 ASSEMBLY AND OPERATION ASSEMBLY AND OPERATION NOTE: 1) The cylinder must be provided with a shut off ...

Scarica la tua

Per scaricare, digitare 2 cifre :