valutazioni - 3, GPA: 4
(
)
)
|
Facilità d'uso
Note: ensure that you leave adequate room to remove and replace the front screen or optional front. Hearth & Home Technologies Inc. • SFE-35 • 4050-313 Rev C • 01/08 2 Fireplace Dimensions 33.75 in. 85.7 cm 1/2 in. (13 mm) L 48 in. 121.9 cm 34 in. 86.4 cm Rough Opening Height 12.75 in. 32.4 cm Rough Opening Depth 22 in. 55.9 cm 36.5 in. 92.7 cm Rough Opening Width 30.5 in. 77.5 cm 33.6 in. 85.4 cm 35 in. 88.9 cm Flush Nailing Flange Note: The bottom surface of this fireplace must be elevated to the level of the finished surface in front of the fireplace to allow access for service and the use of optional fronts. 12.5 in. 31.8 cm Unit Front Unit Top Note: Nailing flanges may be hand-bent to accommodate framing for different styles of optional decorative fronts. Refer to decora- tive front installation manuals for details. If the fireplace will be inset, add .5 in. (13 mm) to the framing depth. Figure 2.1 Fireplace Specifications and Framing Dimensions Hearth & Home Technologies Inc. • SFE-35 • 4050-313 Rev C • 01/08 6 Hearth & Home Technologies Inc. • SFE-35 • 4050-313 Rev C • 01/08 Ensure the appliance is connected to a properly grounded electrical outlet on a minimum 15 AMP circuit. If a new outlet is required, it should be installed by a qualifi ed electrician according to applicable building codes. A. Remote Control Note: If the fi replace does not respond to the hand held control see “Remote Control Initialization” below. This equipment has been tested and found to comply with the limits for class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in residential installation. This equipment generates and uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Re-orient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help. B. Remote Control Initialization This procedure is required only when the unit is installed or the transmitter is replaced and is not affected by the loss of power. • Ensure that power is supplied through main service panel. • Place fresh batteries in the transmitter. • Access the LEARN button by removing the front screen. • Press and hold down the learn button. You will hear a beep. • Press a button on the hand-held transmitter. • Release the learn button when you hear the long beep. • This completes the remote control receiver/transmitter initialization. C. Control Usage The controls operate the fi replace modes. • The fl ame effect and backlog/embers are turned ON/OFF by alternate action of the FLAME button on the remote transmitter. • The heater/blower and front embers are turned ON/OFF by alternate action of the HEATER button on the remote transmitter. • The optional wall FLAME switch provides manual operation (ON/OFF) of the fl ame effect. • The optional wall HEAT switch controls the front embers and activates the optional remote wall thermostat. • Set the thermostat to the desired room temperature. The optional wall switches/thermostat are in parallel with the remote control relays. The wall switches MUST be OFF for the Remote Transmitter to control the fi replace. Note: While the heater is ON the embers in front will glow. Ensure the heater is OFF when unattended. Learn Button FLAMES HEATER 3 OPERATING INSTRUCTIONS 4 Electrical Wiring X1 Projector LampS7 Motor M Interlock on Media Cabinet only Remote Receiver P1 Flame Power Supply Module Heat RD Hot Line Ground Neutral NEMA-5 IEC 320 C13/C14 12 VOC Power Supply J1 Flame Heat Terminal Strip ON WH WH RD 1 5 4050-309 Wall Switch Branch Circuit Ember Bed & Back Log R2 4050-310 Wall Thermostat LED LED LED D1 R1 Heater-Blower Heater Hi Limit Heat Indicator LED LED LED Motor M 5 Service Instructions WARNING! Disconnect power at circuit breaker before attempting any maintenance or cleaning to reduce the risk of fire, electrical shock or personal injury. A. Replacing the Light Bulb This appliance uses a single 12 Volt, 35 Watt, MR-16 bulb. The bulb is located behind the smoke shield. A spare is provided with the unit. Replacement bulbs (Part No. 4050-123) are available through your Simplifyre dealer. • Turn off power to the unit at the main service panel. • Let the fireplace cool if it has been operating. • Release the spring pins and remove the upper shield. • Remove the two screws o...
Questo manuale è adatto anche per i modelli :Elettrico - SIMPLIFYRE SFE-35 (636.23 kb)