valutazioni - 1, GPA: 3
(
)
)
|
Facilità d'uso
• The power can then be supplied from the switch box to the appliance using a minimum of 14-3 with ground wire. • At the switch box connect the black (hot) wire and red (switch leg) wire to the wall switch as shown. • At the appliance connect the black (hot), white (neutral) and green (ground) wires to the junction box as shown. • Add a 1/4 inch insulated female connector to the red (switch leg) wire, route it through the knockout in the face of the junction box, and connect to the top fan switch connector (1/4 inch male) as shown. • Feed the necessary length of wire through the connector. • Make all necessary wire connections to the junction box/receptacle and assemble the junction box/receptacle to the outer shell. appliance: • Remove the screw attaching the junction box/receptacle to the outer shell, rotate the junction box inward to disengage it from the outer shell (see Figure 10.3). • Pull the electrical wires from outside the appliance through this opening into the valve compartment. NOTE: Do NOT wire 110VAC to wall switch. Red Red Black Black Green Green White White Red Black Green White SWITCH BOX JUNCTION BOX POWER SUPPLY WIRES SWITCH MINIMUM 14-3 AWG WITH GROUND Hearth & Home Technologies, Inc. • Bravo, Aztec • InD • 703-900 Rev. N • 8/06 31 A. Mantel Projections Figure 11.1 shows the minimum vertical and corresponding maximum horizontal dimensions of appliance mantels or other combustible projections above the top front edge of the appliance. 11Finishing 1/2 INCH NON-COMBUSTIBLE BOARD REQUIRED ON UNIT FACE FINISHING EDGE TRIM COMBUSTIBLE MATERIALS MAY CONTACT AND COVER FRONT AND SIDE AREAS BELOW GLASS/FRONT NAILING TABS Figure 11.3 Noncombustible Facing Diagram 1 INCH MINIMUM TO VENT PIPE 31 CEILING 3 7/8 14 12 13 17 9 1/8 MIN. 3 1/8 11 9 10 7 5 6 TOP OF FINISHING STRIP TOP OF UNIT 16 18 15 8 Fire Risk. Finish all edges and fronts to clearances and specifi cations listed in manual. WARNING • Black metal appliance front may be covered with noncombustible material only. • Do NOT overlap combustible materials onto appliance front. • Install combustible materials only up to specifi ed clearances on top, front and side. • Seal joints between the fi nished wall and appliance top and sides using only a 300oF minimum sealant. Figure 11.2 Mantel Leg or Wall Projections (Acceptable on both sides of opening.) Figure 11.1 Clearances to Mantels or other Combustibles above Appliance B. Facing Material Fire Risk. Do NOT obstruct air inlet or outlet grilles. Do NOT modify grilles. • Modifying or covering grilles could cause temperature rise and fi re hazard. WARNING Finishing materials must not interfere with: • Air fl ow through grilles or louvers. • Operation of louvers or doors. • Access for service. WARNING Risk of Fire • Non-combustible clearances MUST be maintained. • Sheetrock, wood or other combustibles must NOT be used as sheathing or facing in the non-combustible zone. • See Section 11 for proper clearances. • See Section 1 for combustible/noncombustible defi nitions. C. Finishing Styles • Drywall or other finishing materials may be fi nished all This model has multiple installation and fi nishing options. The following section describe three basic installations. the way up to the finishing edge trim or unit front face, but MUST NOT extend inside of finishing edge trim. Note: A 1/2 inch clearance must be maintained between combustible materials and the front face of the fireplace. OPTION A: Flush Wall Finish Kiva-style finished in a straight wall (see Figure 11.4). • Finishing materials may be fastened or secured to unit below the glass/front opening. CAUTION Finishing materials cut inside the provided template will cause the door to not fit. Figure 11.4 Flush wall installation • Unit is installed using framing dimensions found in Figure 3.2. • Do not use nailing tabs provided on unit sides for Option A. • Nailing tabs found in manual bag assembly or in cardboard sleeve of packing. Install nailing tabs using screws on upper unit sides (see Figure 11.3). • This places unit back 1/2 inch from framing studs such that drywall or other material can be brought directly across non-combustible board up to finish edge trim. WARNING Fire Risk. 1/2 Inch non-combustible board installed on front face of fireplace MUST remain if using combustible fi nishing materials. • A cardboard template is printed on unit shipping carton and may be used to help cut drywall or other finishing materials. Simply cut along line and use it as a template. OPTION B: Kiva-style Arch The second installation option requires the construction of a kiva-style arch. This option recesses the unit into the wall such that construction of a hearth is not necessary (see Figure 11.5). Figure 11.5 • Framing depth increases from that shown in Figure 3.2, (Dimension C). Dimension C will vary depending on the depth of the desired kiva-style arch (see Figure 11.5). • Once depth of desired kiva-style arch is determined (minimum of 3-3/32 inches and maxi...
Questo manuale è adatto anche per i modelli :Elettrico - Aztec (3.53 mb)