This is an unvented gas-fired heater. It uses air (oxygen) from the room in which it is installed. Provisions for adequate combustion and ventilation air must be provided. Refer to page 6. WATER VAPOR: A BY-PRODUCT OF UNVENTED ROOM HEATERS Water vapor is a by-product of gas combustion. An unvented room heater produces approximately one (1) ounce (30ml) of water for every 1,000 BTU’s (.3KW’s) of gas input per hour. Refer to page 6. SR-30T SHOWN Installer: Leave this manual with the appliance. Con

1. The chimney must be lined and sized properly. Most masonry chimneys are over sized and absorb too much heat to be considered a proper vent. If you have any doubts line the chimney with the right size liner. If it's unlined you must line it. 2. Use an insulated liner when the chimney is on the outside, three sides exposed to the weather, and there is no clay liner in the chimney. The insulation will help keep the flue gases warmer. Insulated Vent Enclosure Vented room heaters installed with th

VENTED ROOM HEATER MODELS RH-50-6 RH-65-6 RH-50C-1 RH-65C-1 EFFECTIVE DATE SEPTEMBER 2003 Installer: Please leave these instructions with the consumer. Consumer: Please retain these instructions for future use. WARNING: If not installed, operated and maintained in accordance with the manufacturer's instructions, this product could expose you to substances in fuel or from fuel combustion which can cause death or serious illness. 12822-2-0903 Page 1 TABLE OF CONTENTS TABLE OF CONTENTS SECTION PAGE

If the gas control is turned to the “OFF” position or gas flow to the appliance is shut off, the pilot cannot be relighted until the safety magnet is deenergized (approximately 60 seconds). There will be an audible “click” when the safety magnet in the gas control is de-energized. Pilot can now be relighted. Repeat steps 5 through 9. 11. Turn gas control knob counterclockwise to “ON”. 12. Turn on all electric power to the appliance. (If applicable) 13. Replace access panel (front panel). Set the

Page 12 12822-2-0903 12822-2-0903 Page 13 PARTS VIEW RH-50 & RH-65 PARTS LIST RH-50C & RH-65C PARTS LIST RH-50C & RH-65C PLEASE NOTE: When ordering parts, it is very important that part number and description of part coincide. INDEX PART INDEX PART NO. NUMBER DESCRIPTION NO. NUMBER DESCRIPTION 1 11723 Diverter Assembly 18 R-6126 Electrode and Wire Assembly 2 RH-802 Down Draft Shield (RH-50C-1 NAT 19 11712 Pilot Tubing (RH-50C-1) & LPG) 19 11713 Pilot Tubing (RH-65C-1) 2 RH-851 Down Draft Shield

re or explosion may result causing property damage, personal injury or loss of life. . Do not store or use gasoline or other .am- mable vapors and liquids in the vicinity of this or any other appliance. . WHAT TO DO IF YOU SMELL GAS . Do not try to light any appliance.. Do not touch any electrical switch; do not use any phone in your building. . Immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s instructions.. If you cannot reach your gas supplier, call the . r

Vertical runs must be supported every 3 feet using wall straps. Slip wall straps loosely on to pipe. Attach installer provided straps to framing members using nails or screws. • The fireplace and venting system should be inspected before initial use and at least annually by a qualified field service person. Inspect the external vent cap on a regular basis to make sure that no debris is interfering with the airflow. Inspect entire venting system to ensure proper function. • Please refer to the fi

WARNING: All previously applied loose material must be removed prior to reapplication. Replacement Loose Material (glowing embers) Part Number LS-18P 15999 LS-24P 15970 LS-30P 15970 Platinum Bright Embers PE-20-1 Note: A single layer of embers is to be used when applying Platinum Bright Embers (alone or in combination with production embers) to the burner. Log Placement LS-(18, 24, 30)P Logs Figure 5 Attention: Do not use Figures 1 to 5 to order replacement logs. Refer to Page 11, Parts List and

Follow the gas supplier’s instructions. • If you cannot reach your gas supplier, call the fire department. – Installation and service must be performed by a qualified installer, service agency or the gas supplier. If the information in this manual is not fol- lowed exactly, a fire or explosion may result causing property damage, personal injury or loss of life. LOG SET FOR UNVENTED GAS LOG HEATER OR VENTED DECORATIVE APPLIANCE MODELS LS-18H-1 LS-24H-1 LS-30H-1 EFFECTIVE DATE MAY 2006 INSTALLER:

4. Place Y Branch (#4) onto two (2) pins on rear log. 5. Compare the completed log installation with the appropriate photo from pages 7 through 9. Review previous steps to make any necessary adjustments. 6. Log placement is completed. Replacement Loose Material (glowing embers) Part Number Note: A single layer of embers is to be used when applying Platinum Bright Embers (alone or in combination with production embers) to the burner. Log Placement LS-(18,24,30)B2-1 Figure 1 The following WARNING