2. Lower bottom louver, lift and hinge forward. 3. Release two glass frame spring clamps at bottom of firebox. 4. Remove glass frame assembly. 5. Place front logs (#1 and #2) between front grate flange and main burner. Align notches on front logs with locator tabs in base. 6. Place middle log (#3) between front and rear loop of burner. Note: Do not place log on top of pilot assembly. 7. Place rear log (#4) on rear log shelf. Bottom flange of log must be placed between the log shelf and burner tu

3. Power can be restored once cleaning work is complete. Troubleshooting Chart CONSULT LOCAL ELECTRICAL CODES TO DETERMINE WHAT WORK MUST BE PERFORMED BY QUALIFIED ELECTRICAL SERVICE PERSONNEL Symptom Problem Solution Snapping noise 1. Unit may have a loose end plate 2. Heater may not be mounted properly 1. Loosen end plate screws . turn after allowing heater to warm, move end plate back and forth, then tighten 2. Loosen heater from wall by turning mounting screws . turn Heater not working 1. He

If the millivolt reading is less than 15 millivolt, replace the thermocouple. b. Defective valve. —If thermocouple is producing more than 15 millivolts, replace faulty valve. 3. Pilotburning,nogastoburner,valveknob“ON”,REMOTE/ OFF/ON switch “ON.” a. REMOTE/OFF/ON switch, wall switch, remote control or wires defective. —Check REMOTE/OFF/ON switch and wires for proper connections. Place jumper wires across terminal at switch. If burner comes on, replace defective switch. If OK, place jumper wires

Route supply wires to the thermostat wiring box (if not already present). 2. Connect one supply wire to one thermostat wire (typically marked L1). 3. Route remaining thermostat wire (typically marked T1) to the baseboard heater. 4. Route remaining supply and ground wire to the baseboard heater. 5. Follow installation instructions for mounting and wiring baseboard heater. Figure 12To Supply Thermostat wiring box Single Pole Thermostat L1 T1To Heater DOUBLE POLE WALL THERMOSTAT 1. Route supply wir

Failure to do so could result in serious electrical shock, burns, or possible death. CAUTION - High Temperature. Keep electrical cords, drapes, and other furnishings away from heater. When using electrical appliances, basic precautions should always be followed to reduce the risk of fire, electric shock, and injury to persons, including the following: 1. Read all instructions before using this heater. 2. Read all information labels. Verify that the electrical supply wires are the same voltage as

Cadet neither assumes, nor authorizes anyone to assume for it, any other obligation or liability in connection with its products other than as set out herein. If you believe your Cadet product is defective, please contact Cadet Manufacturing Co. at 360-693-2505, during the warranty period, for instructions on how to have the repair or replacement processed. Warranty claims made after the warranty period has expired will be denied. Products returned without authorization will be refused. Parts an

3. Undernocircumstancesshouldthisappliancebeoperatedwithout the glass front or with a broken glass front. Replacement of the glass (with gasket) as supplied by the manufacturer should be done by a qualified service person. 4. Do not abuse the glass by striking or hitting the glass. WARNING: Do not use abrasive cleaners on glass. Do not attempt to clean glass when glass is hot. It is not unusual for your gas fireplace to give off some odor the first time it is burned. This is due to the curing of

Failure to do so could result in serious electrical shock, burns, or possible death. CAUTION - High Temperature. Keep electrical cords, drapes, and other furnishings away from heater. When using electrical appliances, basic precautions should always be followed to reduce the risk of fire, electric shock, and injury to persons, including the following: 1. Read all instructions before using this heater. 2. Read all information labels. Verify that the electrical supply wires are the same voltage as

If replacing an existing heater check the labels of the old heater and replace using same voltage. Hooking a 240 volt heater to a 120 volt power supply will drastically reduce the heater’s output. Hooking a 120 volt heater to a 240 volt power supply will destroy the heater. WATTAGE (FOR MODEL 8F2025) Model 8F2025 is a multi-watt unit configured for either 2500 or 2000 watts. The heater is factory set for 2500 watts, but the instructions vary depending on your desired wattage and which side you a

WIRING COMPARTMENT COVER Figure 2 3. Remove the slotted knockout closest to the sup ply wires and install a strain relief connector (See Figure 3). Figure 3 4. Pull supply wires through the connector and secure leaving 6 inch wire leads for later use (See Figure 4). SUPPLY WIRES JUNCTION BOX GROUND SCREW Figure 4 5. Mount the heater securely to the wall with nails or screws going into at least two wall studs (See Figure 5). The back of the heater has “star punch” dimples that allow nails or scre