valutazioni - 4, GPA: 3
(
)
)
|
Facilità d'uso
Repeat for bottom spring latches and pull the louvers outward. To install or replace items removed, simply reverse the procedures above. Removing Glass Door If replacement of glass is necessary, the entire assembly, glass and frame, must be replaced. If glass is broken, wear gloves and tape the remaining fragments onto the frame. 1. Remove screen assembly by pushing the rod either left or right and then down and forward to remove screen/rod assembly from the firebox. Set assembly aside. 2. Lift up on latches to unlock. There are two on top of firebox and two below firebox that hold glass door in place (see Figure 41). 3. While holding glass door to prevent it from falling and causing injury, remove the five screws from the hinge located on the left side of door frame assembly (see Figure 41). 4. Remount the new frame at the hinge with five new screws before closing door. This will ensure seating of the gasket. 5. Close glass door frame. Lock latches by placing the bar under the tab on door and pushing down and back on latch (see Figure 41). 6. Replace screen/rod assembly by reversing step 1. 7. Replace louvers by reversing procedure under Removing Louver Panels. Cleaning Glass Door See Cleaning and Maintenance on page 24. Installing Brick liner Models BL42DA(SA) and BL42DHA(SA) WARNING: If fireplace has been running, turn off and unplug fireplace. Let cool before installing brick liner. You may purchase brick liner from your local retailer or see Accessories, page 29. CAUTION: Always handle brick panels with two hands. Do not force brick panels into place. Excessive force will break brick panels. 1. Remove top and bottom louvers to allow access to door latches. 2. Unlock door latches and open glass door. See steps 1 and 2 of Removing/Replacing Glass Door. Fireplace Installation Continued Remote Control Unit Battery Cover Terminal Wires Battery Housing 9-Volt Battery LockUnlock Figure 39 - Installing Alkaline Battery in Hand-Held Remote Control Unit Latch Hinge Screw Glass Frame Assembly Figure 41 - Removing/Replacing Glass Door Spring Latch Louver Panel Figure 40 - Removing Louver Panel 3. If installing brick liner in new fireplace, go to step 4. If installing brick liner in an existing fireplace, carefully remove logs, lava rock, and ember material. 4. Remove three screws from deflector shield on the inside top of firebox. Set shield and screws aside. 5. Install rear brick panel first. Rest bottom edge of panel on back edge of grate (see Figure 42). 6. Install left side brick panel by sliding it between burner assembly and side of fireplace (see Figure 42). 7. Install the right brick panel using the same method described in step 6 for the left brick panel. 8. Replace deflector shield using screws removed in step 4. 9. Install logs, lava rock, and glowing embers (see Installing Logs, Lava Rock and Glowing Embers). 10. Close glass door, lock latches on top and bottom of door and replace screen (see steps 5 and 6 of Removing/Replacing Glass Door, page 19). 11. Close top and bottom louvers. Installing logs, lava rock and glowing embers Each log is marked with a number. These numbers will help you identify the log when installing. It is very important to install these logs exactly as instructed. Do not modify logs. Only use logs supplied with fireplace. Open louvers, remove screen, unlock door latches, and open glass door. See Removing/Replacing Glass Door, steps 1 and 2 on page 19. Install logs according to instructions for fireplace model numbers. 1. Place log #1 (left base log) onto pin on left side of burner as shown in Figure 43. 2. Place log #2 (right base log) onto pin on right side of burner as shown in Figure 43. 3. Place logs #3 (left front log) and log #4 (right front log) onto pins as shown in Figure 44. 4. Place log #5 (right rear log) onto pins on right rear of burner (see Figure 45). Rest log #6 (middle crossover log) on top of log number 2 as shown in Figure 45. 5. Place back end of log #7 (left rear log) onto pin on left rear burner and rest front onto log #1 as shown in Figure 46, page 21. Fireplace Installation Continued 12 Left Side Brick Panel Figure 43 - Installing Logs No. 1 and No. 2 34 Rear Brick Panel Figure 42 - Installing Brick Panels Figure 44 - Installing Logs No. 3 and No. 4 56 Figure 45 - Installing Logs No. 5 and No. 6 6. Rest log #8 (left crossover log) onto log #3 and rest log #9 (right crossover log) onto logs #4 and #5 as shown in Figure 47. 7. Pull ember material apart into pieces no larger than a dime. Place these pieces loosely and sparingly directly onto the exposed front section of the burner (see Figure 48). This will create the glowing ember appearance as the flame touches the ember material. Do not block air slots by using too much ember material in one area. It is not necessary to use all of the ember material provided. NOTICE: Do not put lava rock on burner or under burner. Placing lava rock on burner will cause performance problems. 8. Close glass door, lock door ...