valutazioni - 3, GPA: 3.3
(
)
)
|
Facilità d'uso
This will ensure seating of the gasket. 5. Close glass door frame. Lock latches by placing the bar under thetab on door and pushing down and back on latch (see Figure 42). 6. Replace screen/rod assembly by reversing step 1. 7. Replace louvers by reversing procedure under Removing Louver Panels, page 21. LockUnlockGlass Frame Assembly Screw Figure 42 - Removing/Replacing Glass Door Hinge Latch Cleaning Glass Door See Cleaning and Maintenance on page 28. INSTALLING OPTIONAL BRICK LINER MODEL BL32D WARNING: If fireplace has been running, turn off and unplug fireplace. Let cool before installing brick liner. This brick liner kit is optional. You may purchase brick liner from your local retailer or see page 37. CAUTION: Always handle brick panels with two hands. Do not force brick panels into place. Excessive force will break brick panels. 1. Remove top and bottom louvers to allow access to door latches. 2. Unlock door latches and open glass door. See steps 1 and 2 of Removing/Replacing Glass Door, column 1. 3. If installing brick liner in new fireplace, go to step 4. If installing brick liner in an existing fireplace, carefully remove logs, lava rock and ember material. 4. Remove three screws from deflector shield on the inside top of firebox. Set shield and screws aside. 5. Install rear brick panel first. Rest bottom edge of panel on back edge of grate (see Figure 43). 6. Install left side brick panel by sliding it between the grate and the side of the firebox (see Figure 44, page 23). 7. Install the right brick panel using the same method described 8. Replace deflector shield using screws removed in step 4. 9. Follow instructions on page 23 to install logs, lava rock and ember material. 10. Close glass door, lock latches on top and bottom of door and replace screen (see steps 5 and 6 of Removing Glass Door, column 1). 11. Close top and bottom louvers. Rear Brick Panel Figure 43 - Installing Rear Brick Panel 116646-01A FIREPLACE INSTALLATION Installing Optional Brick Liner Model BL32D (Cont.) Installing Logs, Lava Rock and Glowing Embers 23 FIREPLACE INSTALLATION Continued Brick Panel Left Side Figure 44 - Installing Side Brick Panels INSTALLING LOGS, LAVA ROCK AND GLOWING EMBERS Each log is marked with a number. These numbers will help you identify the log when installing. It is very important to install these logs exactly as instructed. Do not modify logs. Only use logs supplied with fireplace. Open louvers, remove screen, unlock door latches and open glassdoor. See steps 1 and 2 of Removing Glass Door, page 22. Install logs according to instructions for fireplace model numbers. 1. Place log #1 (rear log) on top of grate. Make sure the notches in the bottom of the log fit over the grate (see Figure 45). 1 2. Rest log #2 (large front log) on the pins on the front part of the grate (see Figure 46). 3. Place log #3 (crossover log) onto the rear and front logs. Make sure it is seated properly on the smooth surface on the front log and on the pin on the back log as shown in Figure 47. 4. Place log #4 (right log) on the pin on the right side of front log as shown in Figure 48. 2 Figure 46 - Installing Log No. 2 3 Figure 47 - Installing Log No. 3 4 Figure 45 - Installing Log No. 1 Figure 48 - Installing Log No. 4 116646-01A 24 OPERATING FIREPLACE Installing Logs, Lava Rock and Glowing Embers (Cont.) For Your Safety Read Before Lighting Lighting Instructions FIREPLACE INSTALLATION Continued 5. Place log #5 (base log) onto the front left part of the grate making sure the notches fit over the prongs of the grate). See Figure 49. 6. Place log #6 (left log) onto two pins on the left side of back and front log. See Figure 49. 7. Place lava rock along sides and front of firebox bottom in areas that are visible only. It is not necessary to use all of the lava rock provided. 8. Pull ember material apart into pieces no larger than a dime. Place these pieces loosely and sparingly directly onto the exposed section of the front burner and along the space between the burner and grate prongs (see Figure 50). This will create the glowing ember appearance as the flame touches the ember material. Do not block air slots by using too much ember material in one area. It is not necessary to use all of the ember material provided. 9. Close glass door, lock door latches, replace screen and closelouvers (see steps 5 and 7 of Removing Glass Door, page 22). 56 Figure 49 - Installing Logs No. 5 and No. 6 Ember Material OPERATING FIREPLACE FOR YOUR SAFETY READ BEFORE LIGHTING WARNING: If you do not follow these instructions exactly,afireorexplosionmayresultcausingproperty damage, personal injury or loss of life. A. This appliance has a pilot which must be lighted by hand. When lighting the pilot, follow these instructions exactly. B. BEFORE LIGHTING smell all around the appliance area for gas. Be sure to smell next to the floor because some gas is heavier than air and will settle on the floor. WHAT TO DO IF YO...