valutazioni - 3, GPA: 3.7
(
)
)
|
Facilità d'uso
Burner orifice clogged 2. Inlet gas pressure is too low 3. Thermopile leads disconnected or improperly connected 4. Burners will not come on in remote position 1. Clean burner (see Cleaning and Maintenance, pages 16 and 17) or replace burner orifice 2. Contact local gas company 3. Reconnect leads (see wiring diagram) 4. Replace battery in transmitter and receiver Delayed ignition burner 1. Manifold pressure is too low 2. Burner orifice clogged 1. Contact local gas company 2. Clean burner (see Cleaning and Maintenance, pages 16 and 17) or replace burner orifice Burner backfiring during combustion 1. Burner orifice is clogged or damaged 2. Damaged burner 3. Gas regulator defective 1. Clean burner (see Cleaning and Maintenance, pages 16 and 17) or replace burner orifice 2. Replace damaged burner 3. Replace gas control Slight smoke or odor during initial operation 1. Not enough air 2. Gas regulator defective 3. Residues from manufacturing processes and logs curing 1. Check burner for dirt and debris. If found, clean burner (see Cleaning and Maintenance, pages 16 and 17) 2. Replace gas control 3. Problem will stop after a few hours of operation Moisture/condensation noticed on windows 1. Not enough combustion/ventilation air 1. Refer to Air for Combustion and Ventilation requirements (page 5) 110361-01E 19 TROUBLESHOOTING Continued OBSERVED PROBLEM POSSIBLE CAUSE REMEDY Heater produces a whistling 1. Turning control knob to HI ponoise when burner is lit sition when burner is cold 2. Air in gas line 3. Air passageways on heater blocked 4. Dirty or partially clogged burner orifice 1. Turn control knob to LO position and let warm up for a minute 2. Operate burner until air is removed from line. Have gas line checked by local gas company 3. Observe minimum installation clearances (see page 8) 4. Clean burner (see Cleaning and Maintenance, pages 16 and 17) or replace burner orifice Dark residue on logs or inside of 1. Improper log placement fireplace 2. Drafts or other air currents affecting flame pattern 3. Air holes at burner inlet blocked 4. Burner flame holes blocked 1. Properly locate logs (see Installing Logs, pages 11 and 12) 2. Eliminate source of drafts around heater 3. Clean out air holes at burner inlet. Periodically repeat as needed 4. Remove blockage or replace burner White powder residue forming 1. When heated, vapors from fur-1. Turn heater off when using within burner box or on adja-niture polish, wax, carpet furniture polish, wax, carpet cent walls or furniture cleaners, etc. may turn into cleaners, or similar products white powder residue Heater produces a clicking/tick-1. Metal expanding while heating 1. This is common with most heating noise just after burner is lit or contracting while cooling ers. If noise is excessive, con- or shut off tact qualified service person 110361-01E TROUBLESHOOTING Continued WARNING: If you smell gas • Shut off gas supply. • Do not try to light any appliance. • Do not touch any electrical switch; do not use any phone in your building. • Immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s instructions. • If you cannot reach your gas supplier, call the fire department. IMPORTANT: Operating heater where impurities in air exist may create odors. Cleaning supplies, paint, paint remover, cigarette smoke, cements and glues, new carpet or textiles, etc., create fumes. These fumes may mix with combustion air and create odors. These odors will disappear over time. OBSERVED PROBLEM POSSIBLE CAUSE REMEDY Heater produces unwanted odors 1. Heater burning vapors from paint, hair spray, glues, cleaners, chemicals, new carpet, etc. (See IMPORTANT statement above) 2. Gas leak. See Warning statement above 1. Open window and ventilate room. Stop using odor causing products while heater is running 2. Locate and correct all leaks (see Checking Gas Connections, pages 10 and 11) Heater shuts off in use (ODS operates) 1. Not enough fresh air is available 2. Low line pressure 3. ODS/pilot is partially clogged 1. Open window and/or door for ventilation 2. Contact local propane/LP gas company 3. Clean ODS/pilot (see Cleaning and Maintenance, pages 16 and 17) Gas odor even when control knob is in OFF position 1. Gas leak. See Warning statement above 2. Control valve defective 1. Locate and correct all leaks (see Checking Gas Connections, pages 10 and 11) 2. Replace control valve Gas odor during combustion 1. Foreign matter between control valve and burner 2. Gas leak. See Warning statement above 1. Take apart gas tubing and remove foreign matter 2. Locate and correct all leaks (see Checking Gas Connections, pages 10 and 11) Burner flame is excessively large and is very near or touches the top of firebox 1. Excessive line or manifold pressure 2. Dirty primary air holes 1. Check manifold pressure and correct as needed 2. Clean burner air holes (see Cleaning and Maintenance, pages 16 and 17). 110361-01E ILLUSTRATED ...
Questo manuale è adatto anche per i modelli :Camini - S26PTA (691.08 kb)