valutazioni - 2, GPA: 4.5 ( )

Produttore : Desa Tech File Size : 996.12 kb File Nome : Lingua di insegnamento:

GLASS DOOR Glass must be cleaned periodically. During start-up it is normal for condensation to form on the inside of the glass causing lint, dust, and other airborne particles to cling to the glass surface. During initial start-up a slight film may form on the glass due to paint curing. The glass should be cleaned several times with a non-amonia, nonabrasive household cleaner and warm water after the first two weeks of operation. Thereafter, clean the glass two or three times during each heating season, depending on the usage and circumstances present. Refer to Removing/Replacing Glass Dooron page 22 of this manual when removing glass door for cleaning. If glass has been broken, carefully remove glass door (see Removing/Replacing Glass Door, page 22). Vacuum all glass pieces with a shop vac. CAUTION: Do not vacuum if pieces are hot. Use only the ceramic glass door replacement intended for this fireplace (see Replacement Parts, page 32 for detail on ordering). No substitutions may be made. See Removing/Replacing Glass Door, page 22 for instructions for replacing glass door. WARNING: Do not operate fireplace with the glass door removed, cracked, or broken. , page 24, to properly replace logs. Replace on page 32. Replacement Parts on page 32. VENTING SYSTEM Conduct annual inspection of the venting system following these guidelines: 1. Check areas of venting system that are exposed to the weather for corrosion (rust spots or streaks and, in extreme cases, holes). Have these items replaced immediately by a qualified service person. 2. Remove the vent cap and shine a flashlight into the vent. Remove any foreign material. 3. Check for evidence of excessive condensation. Continuous condensation can cause corrosion of caps, pipes, and fittings and can be caused by having excessive lateral runs, too many elbows, or exterior portions of the system being exposed to cold weather. 4. Inspect joints to verify that no pipe section or fitting has been disturbed and loosened. Check mechanical supports such as wall straps for rigidity. WARNING: Handle glass door panel with care. Do not strike, slam, or otherwise abuse glass. Do not operate fireplace with the glass door removed, cracked, or broken. WARNING: Do not use abrasive cleaners as this may damage glass. Use a non-abrasive household glass cleaner to clean glass. Do not clean glass when hot. 28 104605 OWNER’S MANUAL TROUBLESHOOTING Note: For additional help, visit DESA International’s technical service web site at Note: All troubleshooting items are listed in order of operation. OBSERVED PROBLEM WARNING: Turn off heater and let cool before servicing. Only a qualified service person should service and repair heater. CAUTION: Never use a wire, needle, or similar object to clean pilot. This can damage pilot unit. POSSIBLE CAUSE REMEDY When ignitor button is pressed, there is no spark at pilot 1. Ignitor electrode not connected to ignitor cable 2. Ignitor cable pinched or wet 3. Piezo ignitor nut is loose 4. Broken ignitor cable 5. Bad piezo ignitor 6. Ignitor electrode broken 7. Ignitor electrode positioned wrong 1. Reconnect ignitor cable 2. Free ignitor cable if pinched by any metal or tubing. Keep ignitor cable dry 3. Tighten nut holding piezo ignitor. Nut is located behind the mounting bracket 4. Replace ignitor cable 5. Replace piezo ignitor 6. Replace pilot assembly 7. Replace pilot assembly When ignitor button is pressed, there is spark at pilot but no ignition 1. Gas supply turned off or manual shutoff valve closed 2. Gas control knob not in PILOT position 3. Gas control knob not pressed in while in PILOT position 4. Air in gas lines when installed 5. Depleted gas supply (propane/LP models only) 6. Pilot is clogged 7. Gas regulator setting is not correct 1. Turn on gas supply or open manual shutoff valve 2. Turn gas control knob to PILOT position 3. Press in gas control knob while in PILOT position 4. Continue holding down gas control knob. Repeat igniting operation until air is removed 5. Contact local propane/LP gas company 6. Clean pilot (see Cleaning and Maintenance, page 28) or replace pilot assembly 7. Replace gas control Pilot lights but flame goes out when control knob is released 1. Gas control knob not fully pressed in 2. Gas control knob not pressed in long 1. Press in gas control knob fully 2. After pilot lights, keep gas control knob enough pressed in 30 seconds 3. Manual shutoff valve not fully open 3. Fully open manual shut-off valve 4. Pilot flame not touching thermocouple, 4. A) Contact local gas company which allows thermocouple to cool, causing pilot flame to go out. This prob-B) Clean pilot (see Cleaning and Maintelem could be caused by one or both of nance, page 28) or replace pilot assembly the following: A) Low gas pressure B) Dirty or partially clogged pilot 5. Thermocouple connection loose at con5. Hand tighten until snug, then tighten trol valve 1/4 turn more 6. Thermocouple damaged 6. Replace thermocouple 7. Control valv...

Scarica la tua

Per scaricare, digitare 2 cifre :