valutazioni - 3, GPA: 4.3
(
)
)
|
Facilità d'uso
Si l'information dans cette Instruction n'est pas suivie exactement, un feu, explosion ou production de protoxyde de carbone peut rEsulter le dommages causer de propriEtE, perte ou blessure personnelle de vie. L'agence qualifiEe de service est esponsable de l'installation propre de cet Equipment. L'installation n'est pas propre et complEte jusqu'a l'opEration de l'appareil converti est chEque suivant les criteres Etablis dans les instructions de propriEtaire provisionnEes avec l'Equipement. Step 1. Turn off the gas supply to the appliance. Step 2. Carefully remove the logs. Exercise care so as not to break the logs. Step 3. Refer to Figure 19. Remove the burner assembly with attached venturi tube. In Canada: The conversion shall be carried out in accordance with the requirements of the provincial authorities having jurisdiction and in accordance with the requirements of the CAN1-B149.1 and .2 installation code. LA CONVERSION DEVRA ETRE EFFECTUEE CONFORMEMENT AUX RECOMMANDATIONS DES AUTORITES PROVINCIALES AYANT JURIDICTION ET CONFORMEMENT AUX EXIGENCES DU CODE D'INSTALLATION CAN1-B149.1 ET.2. Gas conversion kits are available to adapt your appliance from the use of one type of gas to the use of another. These kits contain all the necessary components needed to complete the task including labeling that must be affixed to ensure safe operation. Kit part numbers are listed here and the following steps detail the conversion procedure. remove tuberegulatorOrificeremove ClipShutterOpening noisrevnoCsaGenaporPotlarutaNtiKsledoM.oNepyTtinU.oNgolataCGDO63EP870BD-KCG6194HGDO24EP870BD-KCG6194H tiKnoisrevnoCsaGlarutaNotenaporP.oNledoMepyTtinUgolataC.oNGDO63EN041BD-KCG5194HGDO24EN041BD-KCG5194H Figure 19 Electronic Appliances Step 4. Dexen Electronic Valves - See Figure 20 and the instructions provided with the kit. Remove and discard the two pressure regulator mounting screws. Remove the pressure regulator and diaphragm. Discard all removed components. Ensure the rubber gasket installed on the back of the replacement pressure regulator is properly positioned. Install the new pressure regulator using the new screws supplied with the kit. Tighten screws to 25 In. lb. torque. Note: Natural gas regulators are identified with a blue dot. Propane regulators have a red dot. Step 5. See Figure 21 and replace the pilot orifice as follows: Remove pilot hood assembly by grasping the hood and pulling the assembly straight up. Under the hood is the pilot orifice. With caution and using a magnetic screwdriver, undo the pilot orifice and remove it from the assembly. Carefully replace the orifice with the one provided with the kit. Press the pilot hood back over the assembly. The orientation should be aligned as shown in Figure 21. Exercise extreme care to prevent damage to or breakage of the ignitor assembly. Note: Propane pilot orifices are identified with a countersink in the head. Natural gas orifices do not have this countersink. See Figure 21. Step 6. (Refer to Figure 19 on page 15 ) A. Remove the orifice from the manifold with a 1/2" deep throat socket. See the following table for orifice sizes for natural and propane models. Figure 22 illustrates the orifice. Use pipe joint compound or Teflon tape on all pipe fittings before installing (ensure propane resistant compounds are used in propane applications, do not use pipe joint compounds on flare fittings). B. Retrieve the burner and slide the venturi tube over the orifice. Secure the burner in place with the clip shown in Figure 19. Step 7. Reassemble the remaining components by reversing the procedures outlined in the preceding steps. Pilot StageterminalPressure-tap(Inlet) Pilot GasOutletSupplyGasInletPressure-tap(Manifold) Burner StageterminalGround(tP) PILOtOutVENtLOtHtPtHtPHIININGas Outletto BurnerregulatorMounting Screw Figure 20 .oNledoMezisecifirOlarutanaporPGDO63E82# .1405)0( GDO24E82# .1405)0( 74# .0785)0( 74# .0785)0( Ne ELECtrONIC PILOtPilotHoodSensorIgnitorPrOPANENAturAL Figure 22 Note: If the ignitor is damaged, a replacement kit is available, order Catalog Number 87L54. Figure 21 NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE. Lennox Hearth Products reserves the right to make changes at any time, without notice, in design, materials, specifications, prices and also to discontinue colors, styles and products. Consult your local distributor for fireplace code information. Printed in U.S.A. © 2006 by Lennox Hearth Products P/N 850,034M REV. D 04/2009 1110 West Taft Avenue • Orange, CA 92865 ...
Questo manuale è adatto anche per i modelli :Camini - ELITE E36ODGNE (1.65 mb)
Camini - ELITE E36ODGNE-H (1.65 mb)
Camini - ELITE E36ODGPE (1.65 mb)
Camini - ELITE E36ODGPE-H (1.65 mb)