valutazioni - 1, GPA: 4
(
)
)
|
Facilità d'uso
N-LIGHT POWER-N N-FAN N-M SIP13 SIP11 SIP7 T-P Transformer Control Panel Flame / Ember On/Off Switch SIP3 SIP2 SIP4 TEM. SIP6 K-H K-P REMOTE N-FLAME L-FLAME Circuit Board Remote Sensor Temperature Sensor Control Panel (power on/off) Control Panel Heater On/Off Switch Relay 1 Relay 2 L-R1 L-R2 L-FAN Heater 1 (L) Heater 2 (L) Fan Motor (L) Flame Motor (L) Light (L) GROUND 104° C 90°C MAIN POWER L1 L L2 N1 N2 N N Wall Thermostat Wall Switch (power on/off) Outside Switches L-M P-L L-LIGHT GROUND SIP13 WARNING Do not install or operate this fi replace through a switch wired in the 120 VAC or 240 VAC circuits. The only approved wiring for a switch is through the low voltage circuit (24 VAC) as shown on Page 14. HOME POWER - SUPPLY 120 VAC FIREPLACE WIRE HARNESS See Power Supply Specifi cations on Page 3. N L1 GROUND YELLOW AND GREEN ORANGE BLACK BLUE BLUE WHITE N L1 N1 N2 L2 120 V 1600 W 120 V AC G GROUND IF THE APPLIANCE IS TO BE HARD WIRED IN, THE POWER CORD MUST BE REMOVED (SEE INSTRUCTION #2 ON PAGE 5). Figure 20 NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE. 11 WIRING DIAGRAM - 240 VOLT Wiring diagrams are provided here for reference purposes only. This information is also provided on schematics attached directly to the appliance on the left side. CAUTION: LABEL ALL WIRES PRIOR TO DISCONNECTION WHEN SERVICING CONTROLS. WIRING ERRORS CAN CAUSE IMPROPER AND DANGEROUS APPLIANCE OPERATION. Figure 21 Circuit Board Wall Thermostat Control Panel Flame / Ember On/Off Switch Control Panel Heater On/Off Switch Wall Switch (power on/off) MAIN POWER L1 L1 L2 L2 N1 N2 N N Control Panel (power on/off) Outside Switches Transformer Remote Sensor Temperature Sensor P-TRA. SIP3 SIP2 SIP4 TEM. SIP7 SIP6 K-H K-P Heater 1 (L) L-R1 Heater 2 (L) Fan Motor (L) Flame Motor (L) Light (L) L-R2 104° C 90°C L-FAN L-M P-L L-LIGHT N-LIGHT N-FLAME L-FLAME POWER-N REMOTE Relay 1 Relay 2 N-FAN N-M T-P SIP13 SIP11 GROUND GROUND HOME POWER SUPPLY 240 VAC WARNING Do not install or operate this fi replace through a switch wired in the 120 VAC or 240 VAC circuits. The only approved wiring for a switch is through the low voltage circuit (24 VAC) as shown on Page 14. L1 = BLACK (POWER) L2 = ORANGE (POWER) G = GREEN (GROUND) N = WHITE (COMMON) N1 = BLUE (COMMON) N2 = BLUE (COMMON) WIRING - 240 VOLT Figure 22 HOME POWER SUPPLY 240 VAC 120 V (L1) + 120 V (L2) = 240 V FIREPLACE WIRE HARNESS 120 VAC 120 VAC WHITE BLACK ORANGE BLUE BLUE YELLOW AND GREEN GROUND N L1 L2 240 V 3000 W GROUND N L1 L2 N1 N2 See Power Supply Specifi cations on Page 3. THE 120 VOLT POWER CORD INSTALLED ON THIS APPLIANCE MUST BE REMOVED (SEE INSTRUCTION #2 ON PAGE 5). G WALL THERMOSTAT & WALL SWITCH WIRING DIAGRAMS (optional kits, see Page 18) 5 V GROUND INSIDE POWER ON/OFF SWITCH (ON CONTROL PANEL) POWER ON/OFF SWITCH (OPTIONAL WALL SWITCH) OUTSIDE RED REDGREEN • When using the manual control panel power on/off switch, the outside power on/off switch (optional wall switch kit) must be in the OFF position. • When using the outside power on/off switch (optional wall switch), the manual control panel power on/off switch must be in the OFF position. • When using the remote control (optional kit), the manual control panel power on/off switch and the outside wall switch (optional kit) must be in the OFF position. Figure 23 5 V INSIDE BLACK OUTSIDE WALL THERMOSTAT A/D GREEN WHITE 1K POTENTIOMETER. GROUND Figure 24 NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE. Installing Wall Thermostat (optional kit, see Page 18) Wire the wall thermostat prior to installing the fi replace. WALL THERMOSTAT WIRING (24 VAC): Install Wall Thermostat per instructions provided with kit and per the following information: 1. Turn off circuit breaker. 2. Remove cover plate located on the left side of appliance. 3. Locate the the black and white wires and pull out the length needed to reach wall thermostat (15 feet max.). 4. Connect the wires to the wall thermostat as shown in Figure 25. Follow instructions provided with wall switch kit. Wall Thermostat Black 5 V Left Side of Fireplace White White Black White Black 50607080905060708090 Figure 25 NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE. Power On/Off Wall Switch Installation (optional kit, see Page 18) Wire the wall switch prior to installing the fi replace. WALL SWITCH WIRING (24 VAC): Install Wall Switch per instructions provided with kit and per the following information: 1. Turn off circuit breaker. 2. Remove cover plate located on the left side of appliance. 3. Locate the 2 red wires and pull out the length needed to reach wall switch (15 feet max.). 4. Connect the red wires to the wall switch as shown in Figure 26. Follow instructions provided with wall switch kit. Red Red Red 5V Red Red Red Figure 26 NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE. TROUBLESHOOTING SYMPTOM POSSIBLE CAUSES WHO PERFORMS CORRECTIVE ACTION CORRECTIVE ACTION 1. Fireplace turns off and will not turn on. Fireplace has overheated. Homeowner The appliance is protected with a safety devi...
Questo manuale è adatto anche per i modelli :Camini - MERIT PLUS SERIES MPE-33R (914.54 kb)
Camini - MERIT PLUS SERIES MPE-33R (914.54 kb)
Camini - MERIT PLUS SERIES MPE-33R (914.54 kb)