Log:
valutazioni - 4, GPA: 4 ( )

Istruzioni per l'uso Coleman, Modello 5076 Series

Produttore : Coleman
File Size : 261.64 kb
File Nome : 95206457-7877-fb24-8da8-0ad15379594a.pdf
Lingua di insegnamento: en
Vai a scaricare



Facilità d'uso


Note: Initial lighting after gas cylinder change can take up to one minute to purge any air that may be in the line. 3. Burner will ignite and be visible. Continue to push control knob in for 30 to 60 seconds and then release knob. Burner must remain on, if not return to Step 1. Warning: Do not lean over appliance while attempting to light. ¦ Install cover. 2. Push in on control knob and push Igniter knob until unit is lighted. Attention: It is not recommended that this appliance be used if winds are in excess of 10 mph. Battery Installation 1. Unscrew red igni- tor button to reveal battery compartment. 2. Install AA battery with positive (+)out- ward. 3. Replace ignitor button finger tight. Note: If burner fails to remain light ed, all valves should be closed and a waiting period of at least 5 min utes should pass before attempting to light. 4. Rotate control knob to LOW or HIGH position as desired. Burner may be lighted with match if needed. Recommernded that a long fireplace match may be used. Shut Down Procedure 1. Rotate control knob (clockwise) to start position. 2. Push in on control knob and rotate (clockwise) to OFF position. 3. Turn LP bottle valve off. Storage Disconnect fireplace from propane tank before long term storage of either the cylinder or the fireplace. 1. Turn cylinder valve off. 2. Disconnect regulator from cylinder. 3. Remove tank from fireplace. 4. Store propane tank in safe manner. Refer to Chapter 5 of Standard for Storage and Handling of Liquefied Gases, ANSI/NFPA 58. Follow all local codes. Always store propane tanks outdoors. 5. Store fireplace in a dry, clean, and safe place. WARNING • BURN HAZARD • Do not touch or attempt any maintenance on Heater for at least one hour after use. • Make sure all controls are off and propane tank has been removed before doing maintenance. Maintenance To enjoy years of outstanding performance from your fireplace perform the following maintenance activities on a regular basis: • Keep exterior surfaces clean. • Use warm soapy water for cleaning. Never use flammable or corrosive cleaning agents. • While cleaning your unit, be sure to keep the area around the burner dry at all times. • Air flow must be unobstructed. Keep controls, burner, and circulating air passages clean. Signs of possible blockage include: – Gas odor. – Fireplace makes popping noises. – Smoky flame. • Spiders and insects can nest in burner orifices. This condition can damage fireplace and render it unsafe for use. Clean burner holes by using a heavy-duty pipe cleaner. Compressed air may help clear away small particles. • Carbon deposits may create a fire hazard. Clean burner with warm soapy water if any carbon deposits develop. • Carbon may form on logs. If this occurs carbon can be removed with warm soapy water or a soft bristle brush. • If fireplace has been left uncovered and is wet from rain, snow, yard sprinklers, etc., allow to dry (at least 30 minutes prior to use). • NOTE: In a salt-air environment (such as near an ocean), corrosion occurs more quickly than normal. Frequently check for corroded areas and repair them promptly. Troubleshooting Problem Possible Cause Solution Burner won’t light Burner won’t stay lit Burner flame is low NOTE: Do not operate fireplace below 0. F. Cylinder valve is closed Open valve Gas pressure is low Turn Cylinder valve OFF and replace cylinder Air in gas line Burner may take 1-2 minutes to light after a propane bottle has been connected Low gas pressure with Cylinder Valve Cylinder is empty. Replace cylinder fully open Igniter fails Use match to light. Obtain new lighter and replace Control knob not fully depressed in Depress control knob firmly in start position start position when lighting burner when lighting Dirt built up around burner Clean dirt from around burner Thermocouple is not operating Replace Thermocouple correctly Gas pressure is low Turn Cylinder valve OFF and replace cylinder Outdoor temperature is less than 40. F Use a full cylinder and tank is less than 1/4 full Supply hose is bent or kinked Straighten hose Control knob not fully ON Turn Control Knob fully on Burner or orifices blocked Clean blockage from burner & orifices Service • Repair to gas passages and associated components should be done only by a qualified service person. • Owner repair & service should be limited and performed only to the following: - Log replacement - Cylinder replacement Warranty Coleman Limited 7-Year Warranty Coleman will repair or replace, at its option, this product or any component found to be defective in materials or workmanship within seven years of the original retail purchase. This warranty is valid for the original retail purchaser from the date of initial retail purchase and is not transferrable. Keep the original sales receipt. Proof of purchase is required to obtain warranty performance. Coleman dealers, service centers, or retail stores offering Coleman products do not have authority to alter, modify or in any way change the ter...


Scrivi la tua opinione del dispositivo



Il messaggio
Il tuo nome :
Inserire le due cifre :
capcha





categorie