valutazioni - 3, GPA: 3
(
)
)
|
Facilità d'uso
If necessary, consult with a qualified inspector. The purpose of the turbo burner is to increase heat output or BTUs of the unit and will only operate when the main burner is functioning. To turn the turbo burner on, simply depress the burner control knob (located in the valve compartment at the left hand side below the piezo ignitor) and rotate the knob counter-clockwise to 'high'. The turbo burner flame can be observed on the reflective surface in the back right corner of the firebox. The burner flame height may now adjusted to achieve the heat output required. Because the flame is very efficient it will burn a very blue, almost transparent colour. To turn off the burner, rotate the control knob clockwise to 'high'; depress the knob and turn to 'off'. The on-off switch is located on the back of the unit at the top left corner on models GDS50 and GS50. When lit for the first time, the fireplace will emit a slight odour for a few hours. This is a normal temporary condition caused by the curing of the logs and the "burn-in" of internal paints and lubricants used in the manufacturing process and will not occur again. Simply open a window to sufficiently ventilate the room. After extended periods of non-operation such as following a vacation or a warm weather season, the fireplace may emit a slight odour for a few hours. This is caused by dust particles in the heat exchanger burning off. Open a window to sufficiently ventilate the room. FIGURE 43 OPERATION / MAINTENANCE MODEL GS50 ONLY SPILL SWITCH TURBO BURNER OPERATION AND MAINTENANCE ALL MODELS OPERATING INSTRUCTIONS 5.Turn gas knob counter-clockwise to pilot. 6.Depress slightly and hold gas knob while lighting the pilot with the push button ignitor. Keep knob depressed for one minute, then release. If pilot does not continue to burn, repeat steps 3 through 5. 7.With pilot lit, depress and turn gas knob counter-clockwise to on. 8.If equipped with remote on-off switch/thermostat, main burner may not come on when you turn valve to on. Remote switch must be in the on position to ignite burner. 9.Turn on all electric power to the fireplace. FLAME ADJUSTMENT KNOB ON/OFF KNOB A. This fireplace is equipped with a pilot which must be lit by hand while following these instructions exactly. B. Before operating smell all around the fireplace area for gas and next to the floor because some gas is heavier than air and will settle on the floor. C. Use only your hand to turn the gas control knob. Never use tools. If the knob will not turn by hand, do not try to repair it. Call a qualified service technician. Force or attempted repair may result in a fire or explosion. D. Do not use this fireplace if any part has been under water. Immediately call a qualified service technician to inspect the fireplace and replace any part of the control system and any gas control which has been under water. • Turn off all gas to the fireplace. • Open windows. • Do not try to light any appliance. • Do not touch any electric switch; do not use any phone in your building. • Immediately call your gas supplier from a neighbour's phone. Follow the gas supplier's instructions. • If you cannot reach your gas supplier, call the fire department. When lighting and re-lighting, the gas knob cannot be turned from pilot to off unless the knob is depressed slightly. 1.Stop! Read the above safety information on this label. 2.Turn off all electric power to the fireplace. 3.Turn the gas knob clockwise to off. 4.Wait five (5) minutes to clear out any gas. If you smell gas including near the floor. Stop! Follow "B" in the above safety information on this label. If you don't smell gas go the next step. 2.Push in gas control knob slightly and turn clockwise to off. DO NOT FORCE. 1.Turn off all electrical power to the unit if service is to be performed. PURGE THE GAS LINE WITH THE GLASS DOOR OPEN. FOR YOUR SAFETY READ BEFORE LIGHTING: WHAT TO DO IF YOU SMELL GAS LIGHTING INSTRUCTIONS TO TURN OFF GAS MAINTENANCE to pilot. 6.Depress slightly and hold gas knob while lighting the pilot with the push button ignitor. Keep knob depressed for one minute, then release. If pilot does not continue to burn, repeat steps 3 through 5. 7.With pilot lit, depress and turn gas knob counter-clockwise to on. 8.If equipped with remote on-off switch/thermostat, main burner may not come on when you turn valve to on. Remote switch must be in the on position to ignite burner. 9.Turn on all electric power to the fireplace. FLAME ADJUSTMENT KNOB ON/OFF KNOB A. This fireplace is equipped with a pilot which must be lit by hand while following these instructions exactly. B. Before operating smell all around the fireplace area for gas and next to the floor because some gas is heavier than air and will settle on the floor. C. Use only your hand to turn the gas control knob. Never use tools. If the knob will not turn by hand, do not try to repair it. Call a qualified service technician. Force or attempted repair may result in a fire or explosi...
Questo manuale è adatto anche per i modelli :Camini - GDS 50-N (842.16 kb)
Camini - GDS 50-P (842.16 kb)
Camini - GS 50-N (842.16 kb)