valutazioni - 3, GPA: 4.3
(
)
)
|
Facilità d'uso
The symptoms of poor performance related to wet wood include: •Difficulty getting a fire going and keeping it burning well • Smokey fires with little flame • Dirty glass • Rapid creosote build-up in the chimney • Low heat output • Short burn times, excessive fuel consumption and blue/grey smoke from the chimney. To help avoid large build-ups of tar and creosote within the stove and the flue system, it is recommended to burn at high output for at least 30 minutes each day. The use of Stovax Protector chimney cleaner will also help to reduce the problem. 6.2 Solid Fuel Burn manufactured smokeless fuels, or anthracite, list as suitable for use with closed heating stoves. Do not burn 'petro-coke' or other petroleum based fuels, as this will invalidate the product guarantee. If you require advice on suitable solid fuels contact your local Approved Coal Merchant. Details can be obtained by ringing the solid Fuel Association advice line on freephone 0800 600 000. Or their web site at 5 MAINTENANCE AND SERVICING 1. GENERAL CLEANING 1.1 We would recommend that your Stockton stove be cleaned fully on a regular basis, according to the level of use. Attention should be given to cleaning the baffle system, flueways and removing ash. Regular cleaning and preventative maintenance will help give many years of safe use. 2. CLEANING GLASS 2.1 While the correct use of the airwash system, and good quality fuel, will generally keep the glass clean when the appliance is used you may sometimes need to clean the glass. 2.2 This can be done as follows. Allow the stove to cool fully, never attempt to clean hot glass. Any deposits can be removed using a soft cloth and Stovax Glass Cleaner. 2.3 Alternatively, it is possible to remove some stains using a soft cloth and warm soapy water, ensure the you do not wet the door sealing ropes. 2.4 Before re-lighting the appliance, dry the glass fully. 2.5 Do not use abrasive cleaner or cleaning pads. 3. CHIMNEY SWEEPING 3.1 We would recommend that to maintain the safe and efficient use of the appliance the flue/chimney is inspected and swept at least once a year. At the end of the heating season it is recommended to strip, inspect and clean the stove as detailed: 4. ANNUAL SERVICE 4.1 Remove the doors from the appliance. 4.2 Carefully remove all of the following internal parts: Internal Baffle, Firebricks and Ashpan. See sections 5 and 6 for the instructions on how to remove the baffles and firebricks. 4.3 Vacuum clean any remaining ash and debris from the inside of the stove. 4.4 Clean the internal surfaces of the stove using a wire brush and scraper as required. Vacuum and brush the resulting debris from the stove then give the inside of the stove a protective coating of light oil, such as WD40®. Take care not to get any oil on to the external paintwork of the appliance. 4.5 Clean the Baffle and Grate parts with a wire brush, and check the parts for any damage. Replace any damaged parts, if required, and coat all parts with a protective coating of light oil, such as WD40®. 4.6 Check and clean, with a soft brush, the Firebricks. Replace any broken bricks. It is normal for some surface damage to occur during use. 4.7 Re-fit cleaned internal parts. 4.8 Remove the glass from the door, see section 7, and discard all old rope seals. 4.9 Remove the door rope seal from the outer edge of the door, clean the old glue from the door sealing rope grove. 4.10 Clean the door glass using Stovax Stove Glass Cleaner and a soft cloth, do not use abrasive cleaners to remove tar or soot deposits from the glass. 4.11 Replace the glass seal with new and re-fit the glass into place in the door. 4.12 Fit new door rope seal, gluing it in place with Stovax Thermic Seal rope adhesive. When fitting new door seals we recommend closing the stove door and leaving for at least 12 hours before using. This allows the adhesive to fully bond to the seal before use. 4.13 Lightly oil the door catch mechanism and hinge pins. Avoid getting oil on to the door seals and glass. 4.14 To refresh painted finishes it is possible to re-paint using Stovax Thermolac Stove Paint. Stainless steel trim parts may be cleaned using Stovax Stainless Steel Cleaner. 4.15 We recommend that only genuine Stovax replacement parts are used to keep your appliance in safe and efficient working order. Your local Stovax dealer will able to provide you with the genuine parts you require. 6 MAINTENANCE AND SERVICING This is a list of the maintenance products you may need to use Task Product Name Stovax Code Number Glass Cleaning Stove glass cleaner 500ml-wipe on Stove glass cleaner-spray on 4111 4103 Preventing Build-up of Creosote in Flue Protector (15 sachets) Protector (1kg tub) 7002 7025 Sealing Flue Pipe Joints Fire Cement-500g tub Fire Cement-600g cartridge 2020 2021 Re-Painting Thermolac Black (400ml aerosol) Thermolac Black (200ml brush on) Thermolac Metallic Blue (400ml aerosol) Thermolac Metallic Brown (400ml aerosol) Thermolac Met...
Questo manuale è adatto anche per i modelli :Camini - 7126 (299.56 kb)