valutazioni - 2, GPA: 4
(
)
)
|
Facilità d'uso
Insert the top flange of the heat shield through the electrical knockout hole from the inside (Figure 7.9). • Attach the junction box bracket to the side of the appliance. See Figure 7.10. Secure with the screws provided in the fastener package. Heat & Glo • EM-415, EM-485 • 33056 • Rev W • 10/08 Figure 7.9 Attach the Heat Shield Bend this tab down 90 degreesBend this half tab down 90 degrees Slide the flanges of the junction box through the slots in the bracket. Figure 7.6 Prepare Junction Box Bracket Figure 7.9 Attach the Heat Shield Bend this tab down 90 degreesBend this half tab down 90 degrees Slide the flanges of the junction box through the slots in the bracket. Figure 7.6 Prepare Junction Box Bracket Figure 7.7 Position Bracket on Junction Box Bend remaining half tab down 90 desgrees. Figure 7.10 Attach the Junction Box Figure 7.8 Secure Bracket to Junction Box G. Installation of Fan Follow installation instructions supplied with fan kit. Heat & Glo • EM-415, EM-485 • 33056 • Rev W • 10/08 25 Chimney must extend beyond combustible roof structure Maintain minimum height of chimney above roof Additional support for tall chimneys Install roof flashing according to minimum requirements Maintain minimum clearances to combustibles as specified Offsets/returns may not exceed 30° from vertical Lock chimney sections together firmly to resist movement Ceiling firestops are required where chimney passes through ceiling or floor Support straps for returns must be secured to adequate framing Termination Cap Storm Collar Offsets and returns must be secured with the screws provided (outer pipe only) 88 Chimney Assembly NOTICE: Chimney performance may vary. • Trees, buildings, roof lines and wind conditions affect performance. • Chimney height may need adjustment if smoking or overdraft occurs. Heat & Glo • EM-415, EM-485 • 33056 • Rev W • 10/08 Additional support for tall chimneys Install roof flashing according to minimum requirements Maintain minimum clearances to combustibles as specified Offsets/returns may not exceed 30° from vertical Lock chimney sections together firmly to resist movement Ceiling firestops are required where chimney passes through ceiling or floor Support straps for returns must be secured to adequate framing Termination Cap Storm Collar Offsets and returns must be secured with the screws provided (outer pipe only) 88 Chimney Assembly NOTICE: Chimney performance may vary. • Trees, buildings, roof lines and wind conditions affect performance. • Chimney height may need adjustment if smoking or overdraft occurs. Heat & Glo • EM-415, EM-485 • 33056 • Rev W • 10/08 Figure 8.1 Typical Chimney System - Guidelines for Chimney System Installation A. Chimney Requirements Determine the chimney components needed to complete your particular installation: Measure vertical distances from the base of the fireplace as shown in Figure 8.2. • Measure the total vertical height of the fireplace installation from the base of the fireplace assembly to • Minimum overall straight height 16.5 ft (5.03 m) the approximate location of the bottom of the termination • Minimum height with offset/return 16.5 ft (5.03 m) cap. • Maximum height 90 ft (27.43 m) • Subtract the effective height of the fi replace assembly • Maximum chimney length between an offset 20 ft (6.1 m) (see Figure 8.2) from the total vertical height to determineand return the overall height of the chimney installation. • Maximum distance between chimney 35 ft (10.67 m) • Create a schematic for your application similar to Figure stabilizers 8.2 showing components required (referring to Table • Double offset/return minimum height 20 ft (6.1 m) 8.1). Figure 8.1 identifies those components and where • Maximum unsupported chimney length 6 ft (1.83 m) used. between the offset and return • Install a ceiling firestop whenever the chimney penetrates • Maximum unsupported chimney height above 35 ft (10.67 m) a floor/ceiling. the fireplace • Maximum unsupported chimney above roof 6 ft (1.83 m) NOTICE: A maximum of two pairs of offsets and returns may be used. WARNING! Risk of Fire! You must maintain 2 in. (51 CAUTION! Risk of Fire and/or Asphyxiation! DO mm) air space clearance to insulation and other combus-NOT connect this fireplace to a chimney fl ue servicing tible materials around the chimney system. Failure to do another appliance. DO NOT connect to any air distribuso may cause overheating and fire. tion duct or system. These actions could cause over heating/fire in the chimney flue, or release of exhaust fumes into the living areas. Table 8.1 HEIGHT OF CHIMNEY COMPONENTS in. mm Chimney Stabilizer SL3 4-3/4 121 Ceiling Firestops FS338 0 0 FS339 0 0 FS340 0 0 Offsets/Returns SL315 13-3/8 340 SL330 15-1/2 394 Roof Flashing RF370 0 0 RF371 0 0 Chimney Sections* SL306 4-3/4 121 SL312 10-3/4 273 SL318 16-3/4 425 SL324 22-3/4 578 SL336 34-3/4 883 SL348 46-3/4 1187 * Dimensions reflect effective height. 20 ft (6.10 m) max. pipe between an offset & return Ceiling fir...
Questo manuale è adatto anche per i modelli :Camini - EM-415 (4.35 mb)
Camini - EM-415H (4.35 mb)
Camini - EM-485TH (4.35 mb)