valutazioni - 3, GPA: 4.3 ( )

Produttore : Regency File Size : 4.94 mb File Nome : Lingua di insegnamento:

Thesizeandpositionofthelog set was engineered to give the appliance a safe, reliable and attractive flame pattern. Any attempt to use a different log set in the fireplace will void the warranty and will result in incomplete combustion, soot ing, and poor flame quality. Logs get very hot and will remain hot up to one hour after gas supply is turned off. Handle only when logs are cool. Turn off all electricity to the appliance before you install grate, volcanic stone, vermiculite, embers and logs. Thisapplianceisnotdesigned to burn wood. Any attempt to do so could cause irrepa rable damage to the appliance and prove hazardous to your safety. If logs are not installed according to the log instal lation instructions, flame impingement and improper combustion could occur and result in soot and/or excessive production of carbon monoxide (CO), a colorless, odorless, toxic gas. NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE. 29 NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE. 29 Figure 53 FRONT OF FIREPLACE REAR BURNER FRONT BURNER Outer Log Notch Location FIREBOX SUBFLOOR Outer Log Notch Location Outer Log Notch Location Outer Log Notch Location Riser - Inner Log Notch Location LOG NOTCH LOCATION RELATIVE TO BURNER Pilot Assembly Riser - Inner Log Notch Location NOTE: INSTALL REAR BURNER FIRST, THEN FRONT BURNER. Figure 55 BURNER POSITIONING REAR BURNER FRONT BURNER PILOT BURNER Note: The burners are not identical. Position them so that the circular burner ports run as shown. Note especially the vertical run of ports relative to the pilot burner. Bracket A on the rear burner will interfere with the pilot burner if an attempt is made to install the rear burner in the front burner’s position. BRACKET A BURNER PORTS NOTE: INSTALL REAR BURNER FIRST, THEN FRONT BURNER. Figure 54 Volcanic Stone Unitized Log Set Proper Burner Flame Appearance Install the unitized log set: a. The bottom of the log set is notched to accommodate the pilot. b. Place the log set so that the four inner notches on the underside of the log set fit over the four risers located on the burner ends. See Figure 53. This procedure is accomplished primarily by feel, as the log set masks the burner risers as it is being installed. c. As a final check for correct log set placement, check that the four outer notches on the underside of the log set fit over the burner tines as indicated in Figure 53. Burner / Grate Location Reference (see Figures 54 and 55) Note: If the burners have been removed for any reason, rear burner must be installed before front burner. See Figures 54 and 55. Glowing Embers Bag of Glowing Embers (rockwool) Separate into Quarter Size (separate) Pieces Figure 52 REFERENCE Firebox Accessories / Parts Cat. No. Model No. Description 88L53 FGE Bag of Glowing Embers 80L42 FDVS Bag of Decorative Volcanic Stone LOG AND VOLCANIC STONE INSTALLATION PROCEDURE: The log set foam package is located in the firebox and the bags of decorative volcanic stone and the glowing embers (rockwool) are located in the control compartment. Refer to the following information and Figures 52 through 55 for detailed placement instructions. Install the decorative volcanic stone and glowing embers (rockwool): Spread the decorative volcanic stone on the simulated brick floor of the firebox around the burners to simulate ashes. Maintain a 1/2 inch (13 mm) gap between the bottom of the horizontal grate section and the top of the pile of decorative volcanic stone. Place a few quartersized pieces of the glowing ember material on the pan burner in front of the burned out area on both sides of the log set. The glowing embers may touch one another, but should not overlap each other. Step 9. INSTALLATION AND REMOVAL OF GLASS DOOR Step 9. INSTALLATION AND REMOVAL OF GLASS DOOR • Do not attempt to substitute the materials used on these doors, or replace cracked or broken glass. • Handle this glass with extreme care! Glass is susceptible to damage Do not scratch or handle roughly while reinstall ing the glass door frame. • The glass door(s) of this appli ance must only be replaced as a complete unit as provided by the manufacturer. Do not attempt to replace broken, cracked or chipped glass sepa rately. • Do not attempt to touch the front enclosure glass with your hands while the fireplace is in use. WARNING Do not operate appliance with theglassfront removed, cracked or broken. AVERTISSEMENT Ne pas utiliser l'appareil si le panneau frontal en verre n'est pas en place, est craque ou brise. Only doors certified with the appliance shall be used. Seules des portes certifiees pour cet appareil doivent etre utilisees. CAUTION: DO NOT abuse glass door by striking or slamming shut. Removing Glass Enclosure Panels (see Figure 56) 1. Remove the top louver assembly by lifting it up and pulling it out. 2. Remove the control compartment access door (see removal instructions on Page 27 -Removing Control Compartment Door). 3. Locate the two (2) latches at the top of the control compartment....

Scarica la tua

Per scaricare, digitare 2 cifre :