valutazioni - 3, GPA: 3.7
(
)
)
|
da questo dispositivo ha anche altre istruzioni :
Facilità d'uso
Refer servicing to qualified personnel only. Do not install the appliance in a confined space, such as a bookcase or built-in cabinet. The TC-TX5 tape deck is designed only for the DHC-MD5 component system Here are some of the features you can use with this tape deck when connected with the DHC-MD5 Mini Hi-Fi component system. Auto Power On/Off Turning on/off the tape deck is synchronized with the DHC-MD5 component system (see page 5). Pressing the a or »on the tape deck turns the power on. CD Synchro Recording You can record a CD to a cassette with easy operation (see page 7). One Touch Play Pressing aor » on the tape deck when the power is off automatically turns the power on and starts tape playback if there is a cassette in the deck (see page 6). Automatic Source Selection You can switch from another source to the tape deck and start playing a cassette just by pressing aor » on the tape deck (see page 6). Timer You can wake up to music or record a radio programme at a preset time. For detail, refer to the sections “Waking up to music” and “Timer-recording radio programmes” in the instructions manual of the DHC-MD5 component system. However, perform the following settings on the tape deck. • DOLBY NR (B-type) TC-TX5 3-858-049-11 (1).EN • The recording side of the cassette (DIRECTION) Remote Control The remote supplied with the DHC-MD5 can operate the tape deck. This system is equipped with Dolby NR.* * Dolby noise reduction manufactured under license from Dolby Laboratories Licensing Corporation. “DOLBY” and the double-D symbol aare trademarks of Dolby Laboratories Licensing Corporation. Table of Contents Getting Started Hooking up the system ......................... 4 Operations Playing a tape.......................................... 5 Recording a CD ...................................... 7 Recording manually ............................... 8 Additional Information Precautions .............................................. 9 Troubleshooting ................................... 10 Specifications ........................................ 11 TC-TX5 3-858-049-11 (1).EN Hooking up the system Do the following procedures 1 to 3 to hook up your system using the supplied cords. DHC-MD5 rear panel 1 2 1 2 3 TC-TX5 rear panel 1 Connect the AU BUS connecting 3 Connect the mains lead to a wall cord to the AU BUS connectors until outlet. it clicks. 2 Connect the audio connecting cords TC-TX5 3-858-049-11 (1).EN to the jacks of the same colour. Playing a tape You can use any type of tape, TYPE I (normal), TYPE II (CrO2) or TYPE IV (metal), since the tape deck automatically detects the tape type (ATS*). * ATS: Automatic Tape Selection. ( ».../a 0) r24POWER DOLBY NR 3 1 Turn the DHC-MD5 component system on. The tape deck turns on automatically. 2 Press ¤on the tape deck and place a recorded tape. Pressing ¤again closes the cassette tray. With the side you want to play facing upward (9p6P0) r 3 Set DIRECTION to Ato play one side. Set it to a* to play both sides. 4 Press a. Press » to play the reverse side. The tape starts playing. * The tape deck stops automatically after repeating the sequence five times. To Press Stop play .. Pause .. Press again to resume play. Fast-forward ., then a(for upper side) or .(for reverse side). Rewind ., then .(for upper side) or a(for reverse side). Find the a(for going forward) or . biginning of a (for going back) during track(AMS)** playback. Remove the ¤. cassette **The Automatic Music Sensor (AMS) feature detects a blank space of more than four seconds between tracks and locates the track quickly. TC-TX5 3-858-049-11 (1).EN Tips • The lamp above ¤lights up in red when a cassette is loaded in the tape deck and goes off when there is no cassette in the tape deck. • Pressing a or »when the power is off automatically turns the power on and starts tape playback (One Touch Play). • You can switch from another source to the tape deck just by pressing aor » (Automatic Source Selection). • To start playing automatically from the beginning of the tape after fast winding (Auto Play), press a while holding down .(for the upper side) or press »while holding down a (for the reverse side). • When you want to reduce the hiss noise in low- level high-frequency signals, set DOLBY NR to ON. Note The AMS feature may not work in the following cases; — the blank space between tracks is four seconds or less. — the sound sources recorded in the right channel are different from that in the left channel as in a KARAOKE tape. — low volume or low sound continues. — the TV is too close to the tape deck. TC-TX5 3-858-049-11 (1).EN Recording a CD — CD Synchro Recording The CD SYNC button lets you record from a CD to a tape easily. You can use TYPE I (normal) or TYPE II (CrO2) tape, since the tape deck automatically detects the tape type. ( ». 0) r25 4 POWER 6DOLBY NR 1 Turn the DHC-MD5 component system on. The tape deck turns on automatically. 2 Press ¤on the tape deck and place a blank tape. Pressing ¤again closes...