valutazioni - , GPA: ( )

Istruzioni per l'uso Black & Decker, Modello CO85

Produttore : Black & Decker
File Size : 355.94 kb
File Nome :

Lingua di insegnamento:

Il documento viene caricato, si prega di attendere

Scarica la tua primo

Il documento viene caricato, si prega di attendere

Scarica la tua primo

Important: For warranty verification, do not remove line cord sticker. UNPACKING BOX CONTENTS 1. Remove the unit from the cardboard packaging. 2. Remove the blade assembly from cardboard insert and any stickers attached to the blade assembly. To replace blade assembly, follow instructions under Care and Cleaning, Replacing Blade Assembly. 3. Verify that you have received 4 mounting washers with 4 mounting screws, (2) 1/2" and (2) 1/4" spacer mounting assemblies. CHOOSING A MOUNTING LOCATION Important: Do not try to open cans or sharpen knives unless the unit is properly mounted. When selecting a mounting location: • Consider your normal work pattern and the possible addition of other under-thecabinet appliances. • To reduce risk of fire or electric shock, do not place any heating or cooking appliance under the unit. • Do not mount near or over a sink. • Do not mount the unit behind, under or in front of under-cabinet lighting appliances. • Be sure to mount the can opener within reach of an electrical outlet. INSTALLING YOUR CAN OPENER Flush Bottom A Overhang Bottom B C 1. First, determine if your cabinet has a flat bottom (A) —or an overhang (lip extending down) bottom (B) . 2. If your cabinet has a flat bottom, you will need to use one 1/2" spacer mounting assembly. 3. If it has an overhang, measure the overhang with a ruler to determine how many 1/2" or 1/4"spacer mounting assemblies you will need. For example, if the measurement is 1", then use two 1/2" spacer mounting assemblies. 4. With the doors of the cabinet open, use the spacer mounting assembly as a guide to mark one rear and one front hole. 5. a. If your cabinet has an overhang: Slide the mounting assembly forward until one side of assembly touches the inside surface of the overhang. b. If your cabinet has a flat bottom: Place the mounting assembly approximately from the front edge of the cabinet. Important: Be sure the can opener is not set too far back. 6. Close the cabinet door, hold the and lift the lever to be sure it clears (C) . 34 F F G CO75Pub600066R1 7/21/06 3:18 PM Page 6 D E 7. Mark the 4 holes through the assembly onto the underside of the cabinet with a pencil (D) . 8. Remove the spacer mounting assembly. 9. Empty the contents from the bottom shelf. Be sure the underside of the cabinet is free of grease or dirt. 10. Cover the countertop to catch wood chips from drilling. Caution: Wear eye protection to prevent injury from shavings when drilling. 11. Make a small starter hole by hammering a nail or using a small drill bit. 12. Hold the 1/4" drill vertically at the hole marks and drill up through the bottom of the cabinet. 13. Place a plastic washer on each screw with the flat side of the washer resting on the cabinet shelf (E) . 14. For a flat bottom cabinet: a. Drop the screw through the drilled hole from inside the cabinet. b. Repeat the procedure with the remaining screw and washer. For cabinets with an overhang: Push the proper number of spacer assemblies onto the screws coming through the cabinet bottom. 15. Line up the 4 holes in the top of the can opener with the exposed screws beneath the spacer assemblies and tightenthe screws into the top of the can opener. 16. Pull out the cord form the cord storage and plug into electric outlet. Your unit is ready for use! OPENING A CAN 1. Lift the piercing lever. 2. Tip the can so that the rim is under the locating post, then push down on the lever, making sure the cutter blade is inside the rim (F) . Note: Because of the hands-free feature, it is not necessary to hold the lever down or hold the can during cutting. However, you may have to support very tall or heavy ca...