valutazioni - 2, GPA: 4
(
)
)
|
Facilità d'uso
Consistency Adjustment 1.) Unplug the machine. 2.) Be sure that product in bowl is within proper fill range.(Above the minimum fill line) 3.) Remove merchandiser. 4.) Change the thickness of the product by turning the screw (D) on the back of the bowl, as shown on fig. P. Turn the screw clockwise for thinner product or counterclockwise for thicker product. The indicator gauge (D1), located on the back of the bowl, shows the degree of adjustment (+/-). (+) = thicker, (-) = thinner Note: This (D1) is an indicator gauge only. To adjust consistency, turn screw on top (D). (Figure P) (Figure Q) Page 8 G & MG Series Granita Machine Cleaning and Sanitizing Procedures ! Warning Disconnect the unit from its power supply prior to cleaning or sanitizing the unit. Failure to do so may result in electric shock. Daily Cleaning (Figure R) For the machine to function properly, it is important that the cleaning procedures be carried out daily, according to the following instructions: 1.) Turn off the / (G, fig. M) refrigeration and / (F, fig. M) freezing switches and empty the bowl of its remaining product; after draining the product from the unit, you can fill the bowl with hot water (not boiling) to help melt off any sugar deposits. Then drain the water prior to proceeding to step (2). 2.) Unplug the unit. 3) Pull out the mixing rod (E) by pushing it slightly backwards to remove it from its position (see fig. Q on pg.8). 4.) Unscrew and remove the two knobs (F) then lower the bowl to drain out any remaining product through the dispensing valve (see fig. R). 5.) Remove and disassemble the dispensing valve: • Remove the pin (G) as shown (see fig. S). Then, remove the handle (B) sliding it from its seat. • Simultaneously apply pressure to the two securing tabs (H) and lift the dispensing valve (C) to pull it out of its position (see fig. T). 6.) Remove the bowl (L) by unscrewing the two knobs (F) and pulling it downwards as shown in fig. U. 7.) Unscrew the securing bolt (M) clockwise. Pull off the auger (N) and remove the shaft seal (O) and the bowl seal (P) (see fig. V). (Figure V) 8.) Remove the drain tray by lifting up on the front edge, while lowering the rear edge, and then lift it off the unit (see fig. W). (Figure S) (Figure T) (Figure U) (Figure W) 9.) Thoroughly wash each part that has been removed in steps 1-8 and the base (Q), as well as the freezing cylinder (R) with warm water and mild dish- washing detergent. Rinse well with clear water and allow to air dry (see fig. X). Avoid the use of abrasive cleaners which can damage the finish. Do not put in dishwasher. Dishwasher may damage some parts such as the clear plastic auger gears and top mixing bar. Reassemble with clean hands. (Figure X) G & MG Series Granita Machine Page 9 Cleaning and Sanitizing Procedures (con’t) 10.) Reassemble the mixing unit back together, according to the following procedures (see fig. Y): • Moisten the bowl seal (P) with water and slip it into place at the back of cylinder with ribs angled toward back of freezer. • Apply food grade lubricant to the inside of the shaft seal (O) and put the shaft seal (O) back on with the flared end of seal toward back of freezer. • Put the auger assembly (N) back on the evaporator. • Secure all the parts in place by screwing on the bolt (M) counterclockwise. 11.) Reassemble the bowl (L), positioning it into place. Make sure that the bowl fits tightly to the bowl seal (see fig. Z). We also suggest that the rear part of the bowl be moistened with water or lightly lubricated at the point where it fits (Figure Z) together with the seal to make it easier to install bowl. Bowl outside 11a.) The lower right and left bowl flanges should fit on the outside of each black tri corner must be over the white angle edge (see fig. AA). The lid cover will not fit properly if this is not cor plastic edge. rectly positioned. 12.) Secure the bowl (L) by keeping it lifted until the bolt (M) is aligned with its hole (S), then tightly screw on the knobs (F) without exerting excessive pressure to avoid cracking the bowl (see fig. BB). 13.) Reassemble the mixing rod (O) so that its gears are aligned with the lower gear ring. This will allow the front pin to fit perfectly in its position on the bowl (see fig. CC). 14.) Reassemble in sequence the parts of the dispensing valve as follows (see fig. DD). • Make sure that the dispensing valve seat is properly lubricated with food-grade lubricant (such as Haynes Lubrifilm). • Put the dispensing valve body (T) in its seat. • Insert the spring (U). • Put the dispensing valve upper body (V) into its position until it completely snaps into place. • Reassemble the handle (B) and insert retaining pin (G) following the same procedures in #5, fig. S. 15.) Reinstall the drain tray (fig. T). Make sure that the condensation drainage tube (J) is reinserted into its correct fixed position, allowing it to drain into the tray. (Figure Y) (Figure AA) (Figure BB) (Figure CC) (Figure DD) Page 10 G & MG ...
Questo manuale è adatto anche per i modelli :Macchine da caffè - G235-2B (6.83 mb)
Macchine da caffè - G23-2B (6.83 mb)